- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Hard Disc Problem in DL380
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-22-2004 12:40 AM
тАО11-22-2004 12:40 AM
I have a DL380 G1, P3x800 dual processor, I have a 18.2Gb and 147Gb SCSI (both Compaq/HP manufac.)
I have also installed a IDE Controller PCI card and have a 140Gb IDE Maxtor drive. I have setup Redhat 8 without problems on the 18.2Gb SCSI.
I have formatted both the big drives IDE/SCSI and mounted them successfully and have been able to copy things onto them from the network.
I originally copied about 50Gb of data over the network to the 147Gb Scsi with no incident.
When I came to move a large chunk of this data from the SCSI to the IDE drive, things went wrong. Most of it copied without a problem, but then the machine froze, the 147Gb SCSI should the red faulty disc light and the IDE light remained on. The machine eventually rebooted (ASR). The 147Gb SCSI then showed up with no error reported.
I then md5sum a large file on the IDE and these caused the server to lock up again and eventually reboot.
What could be the problem?
Sorry for the lengthy description, I would very much appreciate any advice.
PS In case relevant, I also get a warning message at boot up:
casm: Corrected Memory Error threshold exceeded (System Memory, Memory Module 1)
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-22-2004 08:10 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-22-2004 08:34 PM
тАО11-22-2004 08:34 PM
Re: Hard Disc Problem in DL380
Could this be related to the memory error?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-22-2004 09:12 PM
тАО11-22-2004 09:12 PM
Re: Hard Disc Problem in DL380
When the machine boots up go to the SCSI's cards interface ... by pressing F8 when prompted ( i think its F8 ). Then set the SCSI card as the boot device.
That should fix it.
If your drives is on a smartarray controller adapt this as appropriate.
Regards
Gerhard
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-22-2004 11:24 PM
тАО11-22-2004 11:24 PM
Re: Hard Disc Problem in DL380
Any ideas?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-23-2004 12:50 AM
тАО11-23-2004 12:50 AM
Re: Hard Disc Problem in DL380
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-23-2004 01:59 AM
тАО11-23-2004 01:59 AM
Re: Hard Disc Problem in DL380
In system configuration it acknowledged the addition of the controller and saved settings but said the Smart array controller was the boot controller.
Upon reboot the system does as before i.e.doesn't boot, presumably becuase it is trying to boot from the IDE drive.
I tried the F8 for the Smart Array ut it only lets me create/edit/delete partions etc.
How can I make the Smart Array have a greater priority than the IDE Drive?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-23-2004 02:04 AM
тАО11-23-2004 02:04 AM
Re: Hard Disc Problem in DL380
In the utility there is an option for "Set as boot controller"
HTH
Gerhard
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-23-2004 02:11 AM
тАО11-23-2004 02:11 AM
Re: Hard Disc Problem in DL380
Sorry was a lil silly there .. i thought of a different card :(
But i went and looked at an ML370 ( Physically ). You go into the bios f9 then to "Standard boot order (IPL)" and under there you can tweak it.
Sorry about the earlier mistake.
Regards
Gerhard
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-23-2004 02:18 AM
тАО11-23-2004 02:18 AM
Re: Hard Disc Problem in DL380
I cant see anywhere about setting boot controller aside from in the System Config and this is setting the SCSI controller as the boot controller anyway.
It says:
Your boot controller has been set to:
Embedded...Compaq Integrted Smart Array Controller
So no luck there I'm afraid.