- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- How to set PXE boot with RBSU on bl280?
ProLiant Servers (ML,DL,SL)
1752781
Members
5908
Online
108789
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-28-2010 09:36 AM
01-28-2010 09:36 AM
I want to enable PXE on my bl280 and can't figure out how. If I SHOW IPL, I see 4 devices, none of which are PXE. If I say HELP SET IPL it implies that I could so a SET IPL PXE 1, but that command tells me I have an invalid parameter.
The manual tells me I can only set something listed in the SHOW IPL list! So the question them becomes how do I add PXE to the IPL list.
I also tried to fiddle around with BOOT which only shows my SATA controller so I then looked at my pci with SHOW PCI but that gives me a syntax error.
Does anyone have a magic decoder ring for all this?
The manual tells me I can only set something listed in the SHOW IPL list! So the question them becomes how do I add PXE to the IPL list.
I also tried to fiddle around with BOOT which only shows my SATA controller so I then looked at my pci with SHOW PCI but that gives me a syntax error.
Does anyone have a magic decoder ring for all this?
Solved! Go to Solution.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-29-2010 12:28 AM
01-29-2010 12:28 AM
Solution
I'm assuming you're in the CLI mode of RBSU? I don't have a system at hand to check, but my thought is that you have disabled PXE on the NIC itself, and that's why it's not an option on the IPL list. You need to enabled PXE ability in the NIC first and then you can use IPL to adjust the boot order.
Use the command 'SHOW CONFIG SCRIPT' to capture all of the commands for the current config and look at those involving the NIC.
Use the command 'SHOW CONFIG SCRIPT' to capture all of the commands for the current config and look at those involving the NIC.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP