- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Installation issue
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-04-2019 07:04 AM
03-04-2019 07:04 AM
Installation issue
Hi,
I try to install Windows Server 2012 R2 on a brand new ML110, i100 Raid, 2 x 1TB, 32GB Ram, but it fails.
Last command is rmdir c:\boot. I checked out c:, but there is no such directory, so he is right, unfortunately.
Whats wrong here?
.iso is directly from Microsoft.
With best regards
Gerhard
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-05-2019 09:22 PM
03-05-2019 09:22 PM
Re: Installation issue
Where do you see the " rmdir c:\boot" command ?
Are you in the recovery mode ? Is the server completing POST
Where are you trying to install the OS ? (Local , SAN)
Have configured Hardware RAID ? if yes, what RAID ?
I am an HPE employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-10-2019 08:09 PM
03-10-2019 08:09 PM
Re: Installation issue
Can you please help us to understand if the issue got resolved or not?
This will help for everyone who are all following your forum.
I am an HPE employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-10-2019 11:00 PM
03-10-2019 11:00 PM
Re: Installation issue
Hi,
when installation starts, there where a command window open. Here I can see whats going on. Few lines before hang up, I see this message.
Lastly it turns out, that the install.wim file is 4.7 GB and it needs a ISOtoUSB program which can handle this correctly. I have one, but this wasn't ok, no error message (hu) but wrong image. Nice, isn't it.
After two attempts with other programs I found RUFUS, This little tool works fine and installation succseeded.
Raid and everything else was ok, I used the open cammand window to check the content of drive c:, the target drive for this installation, works fine. It was also my first idea, that the raid/drive/controller causes some problems.
With best regards
Gerhard