- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Intel 82801FR SATA Raid Controller Driver
ProLiant Servers (ML,DL,SL)
1748201
Members
3080
Online
108759
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-17-2008 05:47 AM
тАО07-17-2008 05:47 AM
Intel 82801FR SATA Raid Controller Driver
Looking to load Server 2003 on an HP DL320 G3 and Raid Controller is not found in Smart start. Does anyone have a link to the Raid Controller Driver. Or another suggestion for setup
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-17-2008 07:21 AM
тАО07-17-2008 07:21 AM
Re: Intel 82801FR SATA Raid Controller Driver
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-17-2008 04:14 PM
тАО07-17-2008 04:14 PM
Re: Intel 82801FR SATA Raid Controller Driver
Is your Server SATA Model (HP embedded 2 Port SATA Controller). Keep in mind that the HP Smart Start CD only works with smart array controller it doesn't work with SATA controllers.
Suggestions for Setup:
- Slipstreaming CD (burning the driver with the OS)if you don't have a floppy drive.
- JBOD to RAID1
What does that mean:
1. Install OS with Embedded SATA RAID Disabled(No Drivers or F6 required) on one Harddrive.
2. Once OS is installed, Extract the Embedded SATA RAID Drivers to a folder.
3. Goto Control Panel-> Add New Hardware->Device is connected->New Hardware->Raid Controller->Have Disk->Browse to the folder where the Embedded SATA RAID Drivers were extracted. Select the .inf file->Install Adaptec Raid Driver.
4. Restart the Server goto BIOS enable the Embedded SATA RAID.
5. Press F8 and goto Sata Raid BIOS->Configure the Drives->Create Array->Raid 0/1 A warning message will appear "Warning: Configuring the drives will erase all Array information from the selected drives, if that drive is part of an array. Arrays using any of these drives as members will be affected! Do you want to continue?(Yes/No):". Press "Y" to continue.
6. If Raid 1 is selected it will ask you what is the Source Disk, select the Right Disk in which OS was installed previously. Warning message might appear again. Select "Y".
7. Rebuild will take sometime, once rebuild is complete restart the server.
Once rebooted Raid would be detected and windows would boot up, in windows it would detect new hardware and Adaptec Raid drivers will be installed. Now Server is built migrated to Raid Successfully.
Suggestions for Setup:
- Slipstreaming CD (burning the driver with the OS)if you don't have a floppy drive.
- JBOD to RAID1
What does that mean:
1. Install OS with Embedded SATA RAID Disabled(No Drivers or F6 required) on one Harddrive.
2. Once OS is installed, Extract the Embedded SATA RAID Drivers to a folder.
3. Goto Control Panel-> Add New Hardware->Device is connected->New Hardware->Raid Controller->Have Disk->Browse to the folder where the Embedded SATA RAID Drivers were extracted. Select the .inf file->Install Adaptec Raid Driver.
4. Restart the Server goto BIOS enable the Embedded SATA RAID.
5. Press F8 and goto Sata Raid BIOS->Configure the Drives->Create Array->Raid 0/1 A warning message will appear "Warning: Configuring the drives will erase all Array information from the selected drives, if that drive is part of an array. Arrays using any of these drives as members will be affected! Do you want to continue?(Yes/No):". Press "Y" to continue.
6. If Raid 1 is selected it will ask you what is the Source Disk, select the Right Disk in which OS was installed previously. Warning message might appear again. Select "Y".
7. Rebuild will take sometime, once rebuild is complete restart the server.
Once rebooted Raid would be detected and windows would boot up, in windows it would detect new hardware and Adaptec Raid drivers will be installed. Now Server is built migrated to Raid Successfully.
If it's not fun, you're not doing it right
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-17-2008 04:20 PM
тАО07-17-2008 04:20 PM
Re: Intel 82801FR SATA Raid Controller Driver
I attached some screenshots in order to create a slipstreaming CD using Nlite.
If it's not fun, you're not doing it right
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP