ProLiant Servers (ML,DL,SL)
cancel
Showing results for 
Search instead for 
Did you mean: 

Library TL891DLX which SCSI board is needed?

SOLVED
Go to solution
Carlos Secades
Occasional Advisor

Library TL891DLX which SCSI board is needed?



Hi,

could you please help me to find the right board for the above Library?
This Library has a LVD/SE SCSI connector.

thanks
CARLOS
8 REPLIES
Prashant (I am Back)
Honored Contributor
Solution

Re: Library TL891DLX which SCSI board is needed?

Hi.

Will this do

64 bit 66 MHz dual channel Wide Ultra III SCSI Adapter - 129803-B21
Compaq Dual Channel Ultra2 - 348757-B21
Compaq StorageWorks single channel LVD SE - KZPCA-AA
Compaq StorageWorks - KZPSA-BB (TL891DX w/HVD 40/80 Upgrade Drives ONLY)
Compaq StorageWorks - KZPBA-CB (TL891DX w/HVD 40/80 Upgrade Drives ONLY)
Dual Channel PCI/Ultra HVD HBA - 157299-B21 (TL891DX w/HVD 40/80 Upgrade Drives ONLY)


Or some thing more specific you are looking for

Regards,
Prashant S.
Nothing is impossible
Prashant (I am Back)
Honored Contributor

Re: Library TL891DLX which SCSI board is needed?


Well visit this link also

http://h18000.www1.hp.com/products/quickspecs/10733_div/10733_div.HTML


SCSI Controllers
Compaq ProLiant servers:
64 bit dual channel Wide Ultra II SCSI Adapter (348757-B21)
64 bit 66 MHz dual channel dual channel Wide Ultra III SCSI Adapter (129803-B21)

Nothing is impossible
Carlos Secades
Occasional Advisor

Re: Library TL891DLX which SCSI board is needed?

Prashant,

thanks a lot for your help. I'm confused with the different SCSI boards.
could you help me with info regarding the 6ports card to connect several servers to the same UPS?

thanks
CARLOS
Prashant (I am Back)
Honored Contributor

Re: Library TL891DLX which SCSI board is needed?

Hi,

Is this what you looking for

http://h18004.www1.hp.com/products/servers/proliantstorage/power-protection/options/

Regards,
Prashant S
Nothing is impossible
Prashant (I am Back)
Honored Contributor

Re: Library TL891DLX which SCSI board is needed?

Hi Carlos,

Can you please be more specfic with your question there and can please explain a bit more on it.

Regards,
Prashant S.
Nothing is impossible
Carlos Secades
Occasional Advisor

Re: Library TL891DLX which SCSI board is needed?

Hi Prashant,

regarding the problem with the UPS I will try to explain what happens:

We have in a rack installed 2 servers and 1 UPS RX3000.
The UPS has a 6Ports Card (Six Port Card (P/N 192185-B21))
We use Compaq UPS Software v1.81 to install the software in the servers. When we run the setup process, the application cannot find any device attached to the serial port (UPS) so when the installation process finish the software cannot find the UPS.
I have tried to attach the same server and serial cable to a different UPs with just 1 port (instead of 6) and during the setup process the COM detection finds the UPS.
Perhaps is the UPS which is having problems but we have already replaced the 6Ports card for a new one and the problem remains...

Any idea what happen?

Thanks a lot for your help
regards
CARLOS
Prashant (I am Back)
Honored Contributor

Re: Library TL891DLX which SCSI board is needed?

Hi,

This will help you.
Check aatachment.Is is unde the follwing paramters confirm


Regards,
Prashant S

Nothing is impossible
Carlos Secades
Occasional Advisor

Re: Library TL891DLX which SCSI board is needed?

Prashant,

thanks a lot for your answer. I will check the 6 ports card serial number.

regards
CARLOS