- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: ML110G3 SCSI and problem with instalation
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2006 10:52 AM
тАО02-14-2006 10:52 AM
ML110G3 SCSI and problem with instalation
During instalation I presing F6 and give floppy (USB-Floppy or USB-Key with bios emulation) with drivers (LSI 1030-IT). Server recognize drive and format partition for me but after it ask me to insert the driver disk into drive a: and stops (not riding from floppy).
Instalation on SATA was successfull.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2006 06:00 PM
тАО02-14-2006 06:00 PM
Re: ML110G3 SCSI and problem with instalation
http://h10018.www1.hp.com/wwsolutions/index.html
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2006 09:02 PM
тАО02-14-2006 09:02 PM
Re: ML110G3 SCSI and problem with instalation
Best regards,
Michael
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2006 03:34 AM
тАО02-15-2006 03:34 AM
Re: ML110G3 SCSI and problem with instalation
We can try with usb even though it is not inlisted option
Refer to this for same.
http://h18004.www1.hp.com/products/servers/platforms/usb-support.html
Where as XP is not supported and it a painfull option to go for installation with the same.
Note:
The issue you are facing is due to floppy (USB one) and check with your usb drive. If it is usb1 thencheck with usb2.
Becaseu same issue was faced by me and i have suggested to used the diff USB.
Even though it is working with other system, which will be same in you case also. i suggest you to check with alternate usb version. If you have usb1 then use usb2.
But i think usb1 will work.
Hope this post helped .
Prashant S.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2006 05:09 AM
тАО02-15-2006 05:09 AM
Re: ML110G3 SCSI and problem with instalation
Same problem to me.
I'm trying to install Win 2003 SBS Standard Portuguese.
I do press F6 during instalation, with one non HP Floppy USB 1.1 Drive.
It "loads" the driver of the Embedded raid controler, but later before the instalation begins it will ask again to insert the floppy disc with the driver.
This time the floppy does'n do anything, even not try to read.
Just keep showing the same message: Instert Floppy drive whith the drivers and press ENTER.
Just don't know how to do it!!
Many thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2006 06:01 AM
тАО02-15-2006 06:01 AM
Re: ML110G3 SCSI and problem with instalation
1) I have instaled system on SATA disk.
2) Now I can install SCSI drivers on clean XP installation
3) Clone SATA to SCSI disk
4) Disconecting SATA
5) Boot from install CD and run repair instalation (fixboot, fixmbr). I had to put ntldr, ntdetect.com and copy symmpi.sys (from USBKey) to c:\Ntbootdd.sys to SCSI disk
6) And its working for me :)
Sorry for my terrible English.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2006 06:46 AM
тАО02-15-2006 06:46 AM
Re: ML110G3 SCSI and problem with instalation
where as issue is with the USB device used mostly that's what i have seen. Where as good you the soln.
:-)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2006 04:06 PM
тАО02-15-2006 04:06 PM
Re: ML110G3 SCSI and problem with instalation
I have come across similar issue but it works if you use a USB 2 compliant Floppy Drive.