ProLiant Servers (ML,DL,SL)
cancel
Showing results for 
Search instead for 
Did you mean: 

ML110G5 windows 2008R2 reboots

SOLVED
Go to solution
gremlin
Occasional Advisor

ML110G5 windows 2008R2 reboots

hi. Troubles with ML110G5 when RAID controller enabled in BIOS windows 2008 reboot in cycle. But when RAID controller is disabled it's all ok. Windows have BSOD with Stop 0x0000007B error and then ML110G5 restarts.
Config: Xeon x3330 4gb 2*250gb
15 REPLIES
Murali_V
HPE Pro
Solution

Re: ML110G5 windows 2008R2 reboots

Hello Gremlin,

Sorry i am not clear if you are trying to enable RAID controller with existing operation system or is it new installation.

if this is new installation this issue is due to the controller drivers refer the following threads for ways to install the operating system:

http://h30499.www3.hp.com/t5/ProLiant-Servers-ML-DL-SL/Proliant-ML110-G5-Embedded-RAID-BSOD-loading-Windows-2003/m-p/5102538#M118947


http://h30499.www3.hp.com/t5/ProLiant-Servers-ML-DL-SL/ML110-G5-embedded-SATA-RAID-drivers-for-Windows-Server-2003/m-p/5089069#M118592


http://h30499.www3.hp.com/t5/ProLiant-Servers-ML-DL-SL/ML110-G5-embedded-SATA-RAID/m-p/4544850#M97271

 

if the operating system already installed and you are trying to enable RAID.. i do not think this is good idea, as making changed to RAID will erase data on hard drives.

However, you may try the options given on the following discussion:

http://h30499.www3.hp.com/t5/ProLiant-Servers-ML-DL-SL/Proliant-ml110-G5-raid-after-os/m-p/4303627#M85293


if you have this issue with the initial installation, please let me know the process of the installation which you are following.

Regards,
Murali Mohan

Was this post useful? - You may click the KUDOS! thumb below to say thank you...
Murali_V
HPE Pro

Re: ML110G5 windows 2008R2 reboots

Hello Gremlin,
Any development on this?
- Murali
Was this post useful? - You may click the KUDOS! thumb below to say thank you...
Michael A. McKenney
Respected Contributor

Re: ML110G5 windows 2008R2 reboots

7B is boot loader error. Did you do the firmware on the server before installing 2008? server board, drives, controller? Do you have all the latest drivers? Is 2008 compatible with ML110 G5?
gremlin
Occasional Advisor

Re: ML110G5 windows 2008R2 reboots

2008 compatible with ML110 G5. I download lastest Easy CD for G5. On CD windows 2008, but i need 2008R2. Does G5 compatible with 2008R2? or 2008 only? thanks
Murali_V
HPE Pro

Re: ML110G5 windows 2008R2 reboots

yes it is supported, check the OS support matrix:

http://h18004.www1.hp.com/products/servers/windows/index.html

Click on - Previous Servers for Ml10 G5 OS support list.
Was this post useful? - You may click the KUDOS! thumb below to say thank you...
gremlin
Occasional Advisor

Re: ML110G5 windows 2008R2 reboots

If G5 support 2008r2 how i can install it(with RAID), If lastest EasyCD for G5 support only 2008?
Michael A. McKenney
Respected Contributor

Re: ML110G5 windows 2008R2 reboots

You need to create the RAID from the ACU on post up.
gremlin
Occasional Advisor

Re: ML110G5 windows 2008R2 reboots

ACU from EasyCD? It show me "no controllers found", but RAID controller enabled in BIOS and I create RAID in HP raid tool(F8 on boot)
Michael A. McKenney
Respected Contributor

Re: ML110G5 windows 2008R2 reboots

You need to load the drivers for EasyCD to work with the controller. Do it from Post ACU
gremlin
Occasional Advisor

Re: ML110G5 windows 2008R2 reboots

You mean load drivers from EasyCD when I install windows 2008r2? Or load drivers when I boot EasyCD?
Ali
HPE Pro

Re: ML110G5 windows 2008R2 reboots

Hi Gremlin,

Windows Server 2008 R2 is not supported through the 100 Series Easy Setup CD at this time. As future ProLiant 100 series products are launched, R2 support will be added.

Use the manual installation procedures to configure ProLiant 100 series servers.

thanks,
Aftab
I work for HP
Looking for a quick resolution to a technical issue for your HP Enterprise products? HP Support Center Knowledge-base – Just a Click Away!
See Self Help Post for more details
Ali
HPE Pro

Re: ML110G5 windows 2008R2 reboots

Ref. : page no. 16 of Installing Windows Server 2008 R2 on ProLiant 100 series servers guide

http://h20000.www2.hp.com/bc/docs/support/SupportManual/c01639594/c01639594.pdf
I work for HP
Looking for a quick resolution to a technical issue for your HP Enterprise products? HP Support Center Knowledge-base – Just a Click Away!
See Self Help Post for more details
Ali
HPE Pro

Re: ML110G5 windows 2008R2 reboots

Hi Gremlin,

what I notice that you are using the embedded sata raid controller and driver is not available under the Same OS (windows 2008 R2)

You need HP Embedded G5 SATA RAID Controller Driver for manual installation.

Try this driver
cp013131.exe (740 KB)
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=15351&prodSeriesId=3577708&prodNameId=3577715&swEnvOID=4024&swLang=8&mode=2&taskId=135&swItem=MTX-1f2b48ef26ed4136ba2ccca720


Hope this helps,

thanks,
Aftab
I work for HP
Looking for a quick resolution to a technical issue for your HP Enterprise products? HP Support Center Knowledge-base – Just a Click Away!
See Self Help Post for more details
gremlin
Occasional Advisor

Re: ML110G5 windows 2008R2 reboots

gremlin
Occasional Advisor

Re: ML110G5 windows 2008R2 reboots

Use driver below