- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- ML310 G4 - Setup of Hardware RAID1
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-11-2007 02:26 AM
тАО07-11-2007 02:26 AM
I want both drives to be setup to a hardware based RAID1 configuration, and I want to use the Smartstart assisted installation to install MS SBS 2003 Standard.
I start the server, I enable the embedded SATA controller, I then press F8 to confugure the drives. I set both drives up to work in a RAID1 configuration and make the array "active". I then reboot the server to run the Smartstart installation. Smartstart then states that "The Primary Controller configuration in your system is not supported by this version of Smartstart". Smartstart v7.80 HP Emebbeded SATA RAID (BIOS V4.7-6 B2067) "INTEL(R) 82801GR SATA RAID CONTROLLER" I have checked the Firmware versions on the server by downloading the latest Firmware CD 7.70. Is what I am trying to do supported on this server..?, it seems that this is the config that most people would use..?.
Can any one tell me how I must set this server up to use hardware RAID1..?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-11-2007 02:48 AM
тАО07-11-2007 02:48 AM
SolutionThe embeddedd SATA Controller Supports RAID 0 and 1.You have to install Windows manually
and load the SATA controller drivers during the installation
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-11-2007 02:55 AM
тАО07-11-2007 02:55 AM
Re: ML310 G4 - Setup of Hardware RAID1
Thanks
Colin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-11-2007 04:32 AM
тАО07-11-2007 04:32 AM
Re: ML310 G4 - Setup of Hardware RAID1
once configure RAID level, install windows press F6 when is asking for additional drivers for RAID
once you press F6 windows is going to asked for the driver (use a floppy drive to included)
driver
http://h18023.www1.hp.com/support/files/server/us/download/26742.html
that's is
regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-26-2007 01:52 PM
тАО07-26-2007 01:52 PM
Re: ML310 G4 - Setup of Hardware RAID1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-26-2007 06:59 PM
тАО07-26-2007 06:59 PM
Re: ML310 G4 - Setup of Hardware RAID1
1.Boot up the server. In BIOS, Press F9 and enter setup, go to the ADVANCED options and ENABLE the SATA controller.
2.When the server reboots, again in BIOS, press F8 at the SATA Controller section and create a RAID1 array. This will setup HARDWARE RAID1. SOFTWARE RAID1 is not advised as it is not as resilient.
3.You cannot use Smartstart 7.80 to build this server as the controller is not supported. You must do a manual install of MS SBS 2003 R2. Once complete, put the Smartstart CD in, and install the HP Smartstart management software.
Hope this is okay... It's the only way to do it as far as I know....