- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: ML350 G3 with RILOE II Card: Virtual Power But...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-15-2008 09:15 AM
тАО04-15-2008 09:15 AM
ML350 G3 with RILOE II Card: Virtual Power Button cable not detected
we have a ML350 G3 with two Xeon 2.8GHz CPUs an 6GB of RAM installed and we can't get the RILOE II card to work properly.
Everything but the virtual power button and virtual media feature works fine. If I try to power down the server or reset it, i get an error message like "virtual power error, vpb cable not detected". If I try to open the virtual media applet, I get the error message "30-pin cable not connected", or so.
As the RILOE II Support Matrix says, the server is fully compatible, it doesn't matter in which slot the card is installed and it doesn't need external power. The 30-pin ribbon cable is connected properly to the system board and the RILOE II board.
The RILOE II Board (incl. Virtual Power and virtual media) works normally in a DL360 G2.
Any idea? Could the RILOE II Board be defective? Or maybe the server system board...?
Thank you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-16-2008 12:20 AM
тАО04-16-2008 12:20 AM
Re: ML350 G3 with RILOE II Card: Virtual Power Button cable not detected
let me see, that card works fine in Dl360 G2?
if so... is the server up to date? I mean System ROM?
regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-16-2008 02:53 AM
тАО04-16-2008 02:53 AM
Re: ML350 G3 with RILOE II Card: Virtual Power Button cable not detected
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-16-2008 03:34 AM
тАО04-16-2008 03:34 AM
Re: ML350 G3 with RILOE II Card: Virtual Power Button cable not detected
if you are using KVM switch - test the virtual power button option without the switch.
Make sure you installed the cable correctly:
Installing a Virtual Power Button Cable (4-pin)
To enable the Virtual Power Button feature of the RILOE II on servers that use a four-pin connector on the server system board, install the Virtual Power Button cable (4-pin) (PN 160011-001):
1. Power down the server and disconnect all power cords to remove power from the server.
22 Remote Insight Lights-Out Edition II User Guide
2. Connect the four-pin connector on the cable to the Virtual Power Button cable connector, located on the rear of the RILOE II.
3. Connect the four-pin connector on the other end of the cable into the four-pin connector on the server system board.
IMPORTANT: Be sure that you do not connect the Virtual Power Button cable to the speaker connection on the server system board.
NOTE: For detailed instructions on the location of the connector on the server system board, refer to the documentation provided with the server.
4. Refer to the server documentation to reassemble the server.
Installing a Remote Insight Cable (30-pin)
To install the Remote Insight cable (30-pin) (P/N 241793-010):
1. Power down the server and disconnect all power cords to remove power from the server.
2. Connect the 30-pin connector on the Remote Insight cable to the Remote Insight connector (30-pin), located on the edge of the board.
3. Connect the 30-pin connector on the other end of the Remote Insight cable to the 30-pin Remote Insight connector on the server system board.
Installing the RILOE II
NOTE: For detailed instructions on the location of the connector on the server system board, refer to the documentation provided with the server.
4. Refer to the server documentation to reassemble the server.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-16-2008 04:58 AM
тАО04-16-2008 04:58 AM
Re: ML350 G3 with RILOE II Card: Virtual Power Button cable not detected
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-16-2008 05:00 AM
тАО04-16-2008 05:00 AM