Skip to ContentSkip to Footer
Start of content
- Community Home
- >
- Servers and Operating Systems
- >
- ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- ML350 G5 + SCO OpenServer 5.0.7 (hpsas)
ProLiant Servers (ML,DL,SL)
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
-
- Forums
-
Blogs
- Alliances
- Around the Storage Block
- Behind the scenes @ Labs
- HPE Careers
- HPE Storage Tech Insiders
- Infrastructure Insights
- Inspiring Progress
- Internet of Things (IoT)
- My Learning Certification
- OEM Solutions
- Servers: The Right Compute
- Shifting to Software-Defined
- Telecom IQ
- Transforming IT
- Infrastructure Solutions German
- L’Avenir de l’IT
- IT e Trasformazione Digitale
- Enterprise Topics
- ИТ для нового стиля бизнеса
- Blogs
-
Quick Links
- Community
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Contact
- Email us
- Tell us what you think
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Enterprise.nxt
- Marketplace
- Aruba Airheads Community
-
Forums
-
Blogs
-
InformationEnglish
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-15-2007 08:13 PM
09-15-2007 08:13 PM
ML350 G5 + SCO OpenServer 5.0.7 (hpsas)
I have a ML350 G5 with e200i SAS raid controller and 3 x 146 Gb RAID5 disks.
I can install SCO OpenServer 5.0.7 with hpsas BTLD driver (from EFS 5.770a) but it only see a 19 Gb disk instead 280 Gb.
When SCO boot show the following information:
%disk type=S ha=0 id=0 lun=0 bus=0 ht=hpsas unit=0
%Sdsk cyls=4729 hds=255 Secs=32 unit=0 fts=stdb
%Sdsk-0 Vnd=HP Prd=LOGICAL VOLUME Rev=1.66
The problem is the same than this other user: http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=1130128
I can install SCO OpenServer 5.0.7 with hpsas BTLD driver (from EFS 5.770a) but it only see a 19 Gb disk instead 280 Gb.
When SCO boot show the following information:
%disk type=S ha=0 id=0 lun=0 bus=0 ht=hpsas unit=0
%Sdsk cyls=4729 hds=255 Secs=32 unit=0 fts=stdb
%Sdsk-0 Vnd=HP Prd=LOGICAL VOLUME Rev=1.66
The problem is the same than this other user: http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=1130128
1 REPLY
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-17-2007 12:10 AM
09-17-2007 12:10 AM
Re: ML350 G5 + SCO OpenServer 5.0.7 (hpsas)
Hello Luis,
Refer:
http://www.unixadmintalk.com/f63/openserver-5-0-7-compaq-ml530-275789/
& the link mentioned in the post within;
Regards,
James.
Refer:
http://www.unixadmintalk.com/f63/openserver-5-0-7-compaq-ml530-275789/
& the link mentioned in the post within;
Regards,
James.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
End of content
United States
Hewlett Packard Enterprise International
Communities
- Communities
- HPE Blogs and Forum
© Copyright 2019 Hewlett Packard Enterprise Development LP