- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: ML350P Gen8 Server health LED flashing Red
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-05-2019 01:30 AM
10-05-2019 01:30 AM
ML350P Gen8 Server health LED flashing Red
I am unable to boot. ILO messages "System Power Fault Detected". I flashed system ROM drivers. ILO still showing old ROM version.
"373","Critical","Power","01/01/1970 00:01","01/01/1970 00:01","8","System Power Fault Detected (XR: 24 00 MID: FF 4D DE FF EA FF FF 4A 4A 0C 0C 00 9E 01 00 01 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00)",
Please help me..
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-06-2019 11:50 PM - edited 10-06-2019 11:55 PM
10-06-2019 11:50 PM - edited 10-06-2019 11:55 PM
Re: ML350P Gen8 Server health LED flashing Red
Hello,
I would request you try to clear the NVRAM and check. If the issue still persists, contact HPE technical team because that riser#1 needs to be replaced.
This How-to describes, how to clear the CMOS and NVRAM using the System Maintenance Switch on the system board:
- power down the server
- disconnect the power plugs
- open the server
- connect the power plugs and power up the server
The following message will be displayed:
Maintenance switch detected in the ON position. The system is being default configured. This may take a few minutes… Power off the server and toggle the maintenance switch to the OFF position.
- shut down the server and disconnect the power plugs
- change position 6 back to “off”
- connect the power plugs and power up the server
If you feel this was helpful please click the KUDOS! thumb below!
Regards,
I am a HPE Employee.
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-07-2019 07:24 AM
10-07-2019 07:24 AM
Re: ML350P Gen8 Server health LED flashing Red
Thanks for quick response.
Unfortunately, it doesn't work for me. What is the riser#1 ? System board ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-07-2019 06:22 PM
10-07-2019 06:22 PM
Re: ML350P Gen8 Server health LED flashing Red
Hello,
I think you have to contact the HPE technical team to fix this issue. I am not sure riser board installs or not on your server.
Please find the attached picture of the system board as well as the "HPE ProLiant ML350p Gen8 Server Maintenance and Service Guide" for your reference.
HPE ProLiant ML350p Gen8 Server Maintenance and Service Guide
http://h20628.www2.hp.com/km-ext/kmcsdirect/emr_na-c03251598-13.pdf
If you feel this was helpful please click the KUDOS! thumb below!
Regards,
I am a HPE Employee.
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-06-2019 09:23 AM
11-06-2019 09:23 AM
Re: ML350P Gen8 Server health LED flashing Red
thanks for your steps, but my hp proliant ml350p gen8 server does not have those power switches, so what can I do?