- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- ML370 and Smart Array 3200
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-28-2003 01:05 PM
тАО08-28-2003 01:05 PM
When it post's I get a 1777 error SCSI port 1: I/O board responding with wrong SCSI ID
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-28-2003 09:50 PM
тАО08-28-2003 09:50 PM
Re: ML370 and Smart Array 3200
Please try by moving the SA3200 to a different slot. If not then clear NVRAM first and then give it a try. You can clear NVRAM by going in F10 and then invoke the advanced mode by holding down the CTRL key and Hit "A". Run system configuration and Clear NVRAM is located under Advanced features.
Regards,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-29-2003 12:48 AM
тАО08-29-2003 12:48 AM
Re: ML370 and Smart Array 3200
do you have properly cable installed betwen RAID controller and Drive Cage ?
Recently I have seen cable with terminator installed there and it was not work ... terminator is not allowed on the cable,because terminating is provided by drive cage and controller.
George
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-29-2003 01:32 AM
тАО08-29-2003 01:32 AM
Re: ML370 and Smart Array 3200
Leon
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-29-2003 10:34 AM
тАО08-29-2003 10:34 AM
Re: ML370 and Smart Array 3200
I am using SmartStart 6.4 and 6.3 with no luck. These are brand new ML370 G3's and it is happening on two of them. I have tried to change the card from slot 1, slot 2 and slot 6 with no luck.
As far as the cable goes. I took it off the onboard SCSI and attached it to the SA3200.
I have also removed the 2 GigE adapters and the 2 Fiber HBA's so this is the ONLY card in a PCI slot.
I have also erased the NVRAM with no luck.
Is there an offline ACU for the SA3200?
HP Case# 3202887520
TIA,
Brad
Help!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-29-2003 10:55 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-29-2003 11:02 AM
тАО08-29-2003 11:02 AM
Re: ML370 and Smart Array 3200
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-29-2003 11:54 AM
тАО08-29-2003 11:54 AM
Re: ML370 and Smart Array 3200
I re-booted to SmartStart 6.2 CD and was able to get it to see the controller and configure the drives.
Thanks!
Brad
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-29-2003 12:21 PM
тАО08-29-2003 12:21 PM
Re: ML370 and Smart Array 3200
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-30-2003 05:53 AM
тАО08-30-2003 05:53 AM