- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: ML5500 system halted
ProLiant Servers (ML,DL,SL)
1753756
Members
4867
Online
108799
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-13-2004 10:38 PM
тАО04-13-2004 10:38 PM
ML5500 with a replacement system board reports an unsupported processor -system halted.
half Gb of RAM
on power up. the bios has been upgraded but to no effect.
any ideas please.??
half Gb of RAM
on power up. the bios has been upgraded but to no effect.
any ideas please.??
Solved! Go to Solution.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-13-2004 11:33 PM
тАО04-13-2004 11:33 PM
Solution
Hi
We can do following :
Solution:
Invoke the ROMpaq Recovery Procedure by performing the following:
1) Set switches 1, 4, 5, and 6 on the server's Configuration Maintenance Switch Pack to the ON position
2) Boot the System ROMPaq diskette available for the specific model server.
3) Listen for two long beeps issued by the System indicating the procedure has begun
4) Listen for a sequence of ascending (increasing) tone beeps after flashing is complete
5) Check for a message in the IMD that will indicate a successful operation is completed (If equipped with one)
6) Power off the server and remove the System ROMPaq diskette.
7) Restore the Configuration Maintenance Switch Pack switches to their original positions.
8) Power up the server and observe for symptoms
Regards,
Prashant S.
We can do following :
Solution:
Invoke the ROMpaq Recovery Procedure by performing the following:
1) Set switches 1, 4, 5, and 6 on the server's Configuration Maintenance Switch Pack to the ON position
2) Boot the System ROMPaq diskette available for the specific model server.
3) Listen for two long beeps issued by the System indicating the procedure has begun
4) Listen for a sequence of ascending (increasing) tone beeps after flashing is complete
5) Check for a message in the IMD that will indicate a successful operation is completed (If equipped with one)
6) Power off the server and remove the System ROMPaq diskette.
7) Restore the Configuration Maintenance Switch Pack switches to their original positions.
8) Power up the server and observe for symptoms
Regards,
Prashant S.
Nothing is impossible
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-14-2004 12:21 AM
тАО04-14-2004 12:21 AM
Re: ML5500 system halted
Hi,
In addition , Please do the follwing workaround, if the above does`nt work.
1. Upgrade the ROM with the latest version available on the web. Given is the weblink.
http://h18000.www1.hp.com/support/files/server/us/download/13949.html
2. Swap with any other same processors
3. Suppress the second processor, make a clear NVRAM and put back the processor.
Regards,
George
In addition , Please do the follwing workaround, if the above does`nt work.
1. Upgrade the ROM with the latest version available on the web. Given is the weblink.
http://h18000.www1.hp.com/support/files/server/us/download/13949.html
2. Swap with any other same processors
3. Suppress the second processor, make a clear NVRAM and put back the processor.
Regards,
George
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-18-2004 10:13 PM
тАО04-18-2004 10:13 PM
Re: ML5500 system halted
Brilliant.
the BIOS sorted it ..
many thanks
C
the BIOS sorted it ..
many thanks
C
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP