ProLiant Servers (ML,DL,SL)
cancel
Showing results for 
Search instead for 
Did you mean: 

Maximum Ventilation Hp Proliant ML350p Gen8 / No Error

SOLVED
Go to solution
ITAtaEngenhari
Occasional Contributor

Maximum Ventilation Hp Proliant ML350p Gen8 / No Error

Good Morning,

Our server, at times, appears to have a very loud noise, apparently when there is a power failure (the server is connected to a no-break). So I have to access it via iLO and turn it off, after a few minutes, I turn on the server and the noise disappears. There is no fault on the HDDs (2xHDDs - RAID 1), the LEDs are green, normal. Is there any procedure, or firmware update BIOS (1.13 Nov 08 2012), driver, etc, which can solve this occasional incident?

Waiting feedback. Thank you!

6 REPLIES
FabioC1
HPE Pro

Re: Maximum Ventilation Hp Proliant ML350p Gen8 / No Error

Hello 

Please, update the BIOS

https://support.hpe.com/hpsc/swd/public/detail?sp4ts.oid=5195931&swItemId=MTX_3a5fbdd653f94fac9e2a12e8dc&swEnvOid=4184#tab2

 

power managemnte is recommended

https://support.hpe.com/hpsc/swd/public/detail?sp4ts.oid=5195931&swItemId=MTX_2f232cb44eeb411c867537ffc9&swEnvOid=4184

 

And firmware of ILO 4.  The ILO 4 managemente the sensors. of the server

 

https://support.hpe.com/hpsc/swd/public/detail?sp4ts.oid=1009143853&swItemId=MTX_f9894f8e67d542afad6fbf8eff&swEnvOid=4184

FabioC1 - HPE Pro

If this helps you with your issue, please click the thumb to register a Kudo.
If it resolves the issue, please consider marking it as an Accepted Solution.
ITAtaEngenhari
Occasional Contributor

Re: Maximum Ventilation Hp Proliant ML350p Gen8 / No Error

Good afternoon,

Firstly thanks Fabricio for the feedback.

I downloaded the respective files for the above links, but unfortunately all reported the following error messages:

"The software will not be installed on this system because the required hardware is not present in the system or the firmware does not apply to this system.
 
iLO Channel Interface driver is not loaded.
 
Press 'Close' to exit Setup. "

"The software is not supported for installation on this system.
 
You must install the iLO Channel Interface driver to use this component.
 
Press 'Close' to exit Setup. "

"The software will not be installed on this system because the required hardware is not present in the system or the firmware does not apply to this system.
 
iLO Channel Interface driver is not loaded.
 
Press 'Close' to exit Setup. "

I await your analysis and feeback.

Thank you!

FabioC1
HPE Pro

Re: Maximum Ventilation Hp Proliant ML350p Gen8 / No Error

Install this driver first 

https://support.hpe.com/hpsc/swd/public/detail?sp4ts.oid=1009143853&swItemId=MTX_e196fcb67e1941de959751786f&swEnvOid=4184

 

 

FabioC1 - HPE Pro

If this helps you with your issue, please click the thumb to register a Kudo.
If it resolves the issue, please consider marking it as an Accepted Solution.
ITAtaEngenhari
Occasional Contributor

Re: Maximum Ventilation Hp Proliant ML350p Gen8 / No Error

Thanks, but unfortunately the error below persists in installing this driver.

"The software is not supported for installation on this system.
 
The iLO Channel Interface Driver must be installed before installing this component.
 
Press 'Close' to exit Setup. "

Jimmy Vance
HPE Pro

Re: Maximum Ventilation Hp Proliant ML350p Gen8 / No Error

You need to install the iLO CHIF driver. Follwoing allong with the OS version of the other drivers listed in this thread you need this

https://support.hpe.com/hpsc/swd/public/detail?sp4ts.oid=5195931&swItemId=MTX_e74f93921947408eb5de783d27&swEnvOid=4184

Or better yet, download the latest Gen8 SPP and it will contain all the latest Proliant drivers for your system

 

 




__________________________________________________
No support by private messages. Please ask the forum!      I work for HPE

If you feel this was helpful please click the KUDOS! thumb below!   
ITAtaEngenhari
Occasional Contributor
Solution

Re: Maximum Ventilation Hp Proliant ML350p Gen8 / No Error

Good evening,

Sorry for the absence, because I was analyzing a new project.
Regarding the last information of the update, it was successful. The forerunners that I informed that occurred error, this time only this:
power managemnte is recommended

https://support.hpe.com/hpsc/swd/public/detail?sp4ts.oid=5195931&swItemId=MTX_2f232cb44eeb411c867537ffc9&swEnvOid=4184

who reported mistake.

These regulations solve the problem in relation to the Maximum Ventilation ?

Thank you!