Migrate raid 1 (two disk) to raid 10 (four disk)

[RicardoFP]

Is it possible to migrate a raid 1 with two disks (1Tb each) to raid 10 with 4 disks? I have a DL380 GEN8 with Smart Array P410i and BBWC, how to do it with CLI or ACU. It is urgent. Thank you

[FabioC1]

 RicardoFP  

you can only spand array not migrate array with P410i 

https://www.youtube.com/watch?v=4wQ3XUTfD-E

Migrate array  only P410, with battery

https://h20195.www2.hpe.com/v2/getpdf.aspx/c04111713.pdf

[RicardoFP]

I Have the BBWC and the licence.

I need to know how make it via ACU or CLI.

step by step 

Thank you

[FabioC1]

Migrate array  only P410, with battery, not P410i

https://www.youtube.com/watch?v=4wQ3XUTfD-E

More information of hpw to expand array  In ACU

https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-c03510253

[Jimmy Vance]

---

@FabioC1 wrote:

Migrate array  only P410, with battery, not P410i

https://www.youtube.com/watch?v=4wQ3XUTfD-E

More information of hpw to expand array  In ACU

https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-c03510253

---

There should be no difference in perfomaing this task with a 410 versus a 410i

NOTE: Whenever you are going to make array changes, make sure you have a valid backup of the data on the array(s)

[RicardoFP · Accepted solution]

This is the solution..... 

A)  ctrl slot=0 show config

     logicaldrive 1 (1.6 TB, RAID 0)

      physicaldrive 1I:1:1 (port 1I:box 2:bay 1, SAS, 900.1 GB, OK)   <= ORIGINAL RAID 0
      physicaldrive 1I:1:2 (port 1I:box 2:bay 2, SAS, 900.1 GB, OK)   <= ORIGINAL RAID 0
      physicaldrive 1I:1:3 (port 1I:box 2:bay 3, SAS, 900.1 GB, OK)   <= NEW DISK
      physicaldrive 1I:1:4 (port 1I:box 2:bay 4, SAS, 900.1 GB, OK)   <= NEW DISK

B) controller slot=0 logicaldrive 1 add drives=1I:1:3,1I:1:4

      logicaldrive 1 (1.6 TB, RAID 0, Transforming, XX% complete)

     After 9 Hours...

C) ctrl slot=0 ld 1 modify raid=1+0

    logicaldrive 1 (1.6 TB, RAID 1+0, Transforming, XX% complete)

    after 9 hours

     logicaldrive 1 (1.6 TB, RAID 1+0)

      physicaldrive 1I:1:1 (port 1I:box 2:bay 1, SAS, 900.1 GB, OK)
      physicaldrive 1I:1:2 (port 1I:box 2:bay 2, SAS, 900.1 GB, OK)
      physicaldrive 1I:1:3 (port 1I:box 2:bay 3, SAS, 900.1 GB, OK)
      physicaldrive 1I:1:4 (port 1I:box 2:bay 4, SAS, 900.1 GB, OK)

[ovn13]

Hi Ricardo,

Did you manage to do it without losing any data?

Regards