- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Ml110 ont booting to raid drive after os setup
ProLiant Servers (ML,DL,SL)
1748181
Members
4040
Online
108759
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2011 09:37 AM
тАО01-14-2011 09:37 AM
Ml110 ont booting to raid drive after os setup
I'm been tring to get a ml110 to boot to the raid drive set after the the server preinstall
all it does is restart the Os install
all it does is restart the Os install
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2011 09:51 AM
тАО01-14-2011 09:51 AM
Re: Ml110 ont booting to raid drive after os setup
Did you set the RAID controller to boot from that partition. In the CMOS, did you set the RAID controller in the boot order after CD/DVD drive. Remove the CD/DVD from the drive and reboot.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2011 10:08 AM
тАО01-14-2011 10:08 AM
Re: Ml110 ont booting to raid drive after os setup
Yes to all
It has an hp smart array p212 installed went thru the smart start setup the raid and logical drives everything seems correct
But strange thing is that in the BIOS it does not offer booting to the raid controller only lists hard drive
It has an hp smart array p212 installed went thru the smart start setup the raid and logical drives everything seems correct
But strange thing is that in the BIOS it does not offer booting to the raid controller only lists hard drive
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2011 10:56 AM
тАО01-14-2011 10:56 AM
Re: Ml110 ont booting to raid drive after os setup
You should see the controller or RAID array in the boot order area. Did you run the firmware on the controller and drives? If not, do it. Are you sure that controller is compatible with the server, enclosures, and drives?
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP