- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Monitoring DL580 G5 using PRTG
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-11-2014 07:37 AM
08-11-2014 07:37 AM
Monitoring DL580 G5 using PRTG
Hello everybody,
i am trying to monitor a DL580 G5 using PRTG Network Monitor. So far everything is fine. I can monitor the server using SNMP Sensor "HP Proliant System State" and getting status of PSU, temperature etc.
But when it comes to the raid controller (P400) i am getting problems reading raid / drive / volume status. I already have installed WBEM provider (9.5.0.0) and management agent (9.40.12.0).
PRTG support says the required OID / OID branch 1.3.6.1.4.1.232.3.2.5.1.1.6.2 is missing.
Hope someone can help me out.
Thanks
Daniel
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-12-2014 06:11 PM
08-12-2014 06:11 PM
Re: Monitoring DL580 G5 using PRTG
Hi,
First question, can PRTG Network Monitor show RAID controller information?
Make sure Raid drivers/firmware and Insight Management Agents are up dated. Use only SNMP and check the status. If that does not work, post a similar question in PRTG forum.
Some links from HP:
HP ProLiant Servers - Finding Object Identifier (OID) of Components on ProLiant Servers
http://h30499.www3.hp.com/t5/Disk-Array/SNMP-MIB-S-for-Smart-Array-P400-RAID-CTRLR/td-p/5200088
Some links from PRTG:
http://kb.paessler.com/en/topic/903-how-do-i-find-out-what-oid-i-need-to-use-for-a-custom-sensor
http://kb.paessler.com/en/topic/653-how-do-snmp-mibs-and-oids-work
http://kb.paessler.com/en/topic/34063-monitoring-raid-disk-hw-on-esxi-5
http://kb.paessler.com/en/topic/33133-monitor-hp-proliant-via-snmp
Thank You!
I am a HP employee.
I work for HPE.
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-13-2014 03:06 AM - edited 08-13-2014 03:10 AM
08-13-2014 03:06 AM - edited 08-13-2014 03:10 AM
Re: Monitoring DL580 G5 using PRTG
yes the sensor shows the disk controller and status "ok". Firmware is up to date.