- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Moving hard drives from Proliant DL380 G3 to G...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-25-2007 11:34 PM
тАО10-25-2007 11:34 PM
Lately we bought some spare DL380 G4 (majority of our servers is DL380 G4, but we still have a few G3) and we would like to use them also as possible backup/failover hardware.
Basically if there would be any problem with server itself we would like to swap hard drives and have the same server up and running.
We did some tests and everything works when we swap hard drives between G4s, however when we try to swap hard drives from G3 to G4 installed Windows 2003 SP2 generates bluescreen and rebootes (I had no chance to note down any error message).
What I have already tried was installing a few drivers on G3 machine like:
- smart array cp 007955 (v. 5.78)
- smart ext cp 007958 (v. 6.4.0.32)
as I though it might be problem with new controller.
Could you advise any action that should be done? Something I should install when running on G3?
Regards
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-26-2007 12:15 AM
тАО10-26-2007 12:15 AM
Re: Moving hard drives from Proliant DL380 G3 to G4
HP Smart Array controllers support drive roaming, which allows administrators to move hard drives and arrays while maintaining data availability. Drive roaming allows administrators to move one or more hard drives that are members of a configured logical drive to a different bay position as long as the new bay position is accessible by the same controller. In addition, it allows administrators to move a complete array from one controller to another, even if controllers are in different servers. This is When BOTH the controllers on different servers are of the same TYPE & the configuration are set to be identical.
I am not aware of any software that will enable this explicitly of different controllers/settings.
Regards.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-26-2007 01:07 AM
тАО10-26-2007 01:07 AM
Re: Moving hard drives from Proliant DL380 G3 to G4
- thank for your reply :) fortunatelly we have no problems when moving hard drives between the same models (G3 <-> G3, G4 <-> G4). Everything even works fine when I use G4 hard drives in G3 servers...
Just wonder what difference between G3 & G4 affects Windows 2003 SP2 in such way (blue screen :) and what drivers should be installed on G3 then to prevent it :)
Regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-26-2007 02:09 AM
тАО10-26-2007 02:09 AM
Re: Moving hard drives from Proliant DL380 G3 to G4
There are Many Differences in the DL380 G3 & G4 server. One & most important one is the Chipset.
G3 has ServerWorks GC -LE Chipset.
&
G4 has Intel E7520 Chipset.
As you may imagine.. the whole base level architecture is different >in turn the drivers are different.
Regards.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-26-2007 03:01 AM
тАО10-26-2007 03:01 AM
Re: Moving hard drives from Proliant DL380 G3 to G4
what is the controller in Dl380 G3 servers?
and the firmware version?
what is the controller in Dl380 G4servers?
and the firmware version?
very important to know
also where are you getting the Blue screens?
when windows is initialization, before login?
regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-26-2007 03:06 AM
тАО10-26-2007 03:06 AM
Re: Moving hard drives from Proliant DL380 G3 to G4
my recommendation update firmware and Proliant support pack(PSP) in G3 servers and G4 servers, before do this HDDs roaming
regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-26-2007 04:29 AM
тАО10-26-2007 04:29 AM
SolutionI think this might be the information you are looking for.
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=724645
Regards,
Brian
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-29-2007 04:53 AM
тАО10-29-2007 04:53 AM
Re: Moving hard drives from Proliant DL380 G3 to G4
Happy Dude, Karlo & Brian_Murdoch - thank you guys for your help.
Before I have started this thread I have tried to find solution here, but I could not... I don't know, Brian, how did you find that thread ("Disk move from 5i to 6i"), but that was exactly I was looking for.
Solution was briliant!
Everythink is working fine now, thx & cu later :)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-29-2007 04:54 AM
тАО10-29-2007 04:54 AM