- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: No Bootable Drive Configured? DL380
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-01-2005 06:43 AM
тАО04-01-2005 06:43 AM
No Bootable Drive Configured? DL380
PIII 1.0ghz, 2gb RAM, Smart Array 3200 Controller Slot 2,
Configured array using Smartstart Disk 7.10
SCSI A array: 4 x 32gb RAID 5, and SCSCI B array: 2 x18gb 1x0 RAID
Updated BIOS ROM to: P17 12/18/2002
Unable to use the Smart Disk to install W2K3 on this server even after configuring the array.
Error options:
1) RBSU - ROM Based Setup Utility, however unable to run as instructed.
2) ORCA - Option Rom Config for Arrays Utilities again this doesn't run as instructed.
3) This Smark Disk 7.1 doesn't support assisted OS install. "If so I did try Smark Disk 5.5 and had same issue"
Recommends booting from CD.
Attempted to boot from W2K3 Entrerprise CD the disk loads the drivers and then beings the Windows Setup process and hangs up there. Never goes beyond this point.
This is where we are stuck. Any advice recommended solutions would greatly be appreciated.
Thanks, JIM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-01-2005 07:35 AM
тАО04-01-2005 07:35 AM
Re: No Bootable Drive Configured? DL380
http://h18004.www1.hp.com/support/files/server/us/subscription/ssdownloads.asp
Configure ACU and SCU than continue with manaul install
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-01-2005 05:36 PM
тАО04-01-2005 05:36 PM
Re: No Bootable Drive Configured? DL380
I believe SS 7.10 will not work on this PIII server, you should try with 5.5. first configure your arrays through ACU, setup BIOS through SCU, select proper boot controller order in SCU, and then start your server with W2K3 CD. use SS 5.5 cd only if you need any driver which W2K3 could not install automatically.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-02-2005 01:48 AM
тАО04-02-2005 01:48 AM
Re: No Bootable Drive Configured? DL380
Perform a manual, no SS, install. We have a document with detailed instructions on our support page. Basically you need to run the system clear, then reconfigure the array, then make a drive disk, then install the OS.
You were awesome with the Doors.
Sorry, Jim, couldn't help myself.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-04-2005 02:57 AM
тАО04-04-2005 02:57 AM
Re: No Bootable Drive Configured? DL380
Just make the RAID configuration via the ROM part of the Integrated Array Conroller.
Afterwards install the operating system. All special drivers, agents or other stuff could be done after the OS is installed.
If the server stuck during setup update the BIOS and check also the CDROM drive Firmware. There is a known issue with TEAC slimlime CD roms and 9.0b fimrware. Update to 9.0C, then it should work. Will attach the SP for CDROM because it is pretty small.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-04-2005 03:17 AM
тАО04-04-2005 03:17 AM
Re: No Bootable Drive Configured? DL380
If you configure array controller via ROM you have to create one logical disk per array (with 100% available space).
regards,
Andrzej