- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: No auto boot on power restore?
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-20-2015 09:42 AM - edited 08-20-2015 11:13 AM
08-20-2015 09:42 AM - edited 08-20-2015 11:13 AM
No auto boot on power restore?
Greetings all,
We have 3 HP Dl 380 G7's clustered running ESXi 5.0 U3 with LeftHand SAN. We would like to make sure these 3 servers NEVER auto-restart when power has been restored after a power fail event. Ideally, we would access remotely via the ILO and power on when the ISCSi network is up and available.
I don't see anything in the ILO, other than auto start or delay, but this is not the functionality we desire. And in the BIOS, the Automatic Power on setting when disabled says it will restore power to its previous state??!
Can this be done on the server (preferred) or should we be looking at the attached UPS functionality?
Thanks in advance.
Buddy
UPDATE: The link below would seem to indicate this could not be done in a G4 server, has this changed in the G7's?
http://h30499.www3.hp.com/t5/ProLiant-Servers-ML-DL-SL/DL380-Auto-Start-Up/td-p/4361405#.VdYXXJeBK2Y
Again, thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-20-2015 12:05 PM
08-20-2015 12:05 PM
Re: No auto boot on power restore?
You should have three options :
Always Power ON
Always Remain OFF
Restore Last Power State
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-20-2015 12:15 PM
08-20-2015 12:15 PM
Re: No auto boot on power restore?
Thanks Jimmy!
Where...in the ILO or BIOS?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-20-2015 12:19 PM
08-20-2015 12:19 PM
Re: No auto boot on power restore?
It is in RBSU (BIOS) under 'Server Availability' - 'Automatic Power-On'