- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: ProLiant 8500: No video or POST
ProLiant Servers (ML,DL,SL)
1752801
Members
5578
Online
108789
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-02-2004 04:20 AM
06-02-2004 04:20 AM
ProLiant 8500: No video or POST
I've been given a ProLiant 8500 that I'm told was working when it was removed from the rack. When I power it up there is no video and no POST. The fans turn on, the drive lights blink momentarily, then three stay lit with green arrows and one stays unlit. All LEDs that I can find inside the system are green. There are no "system interconnect status indicators" lit. I've tried the following already:
* Removed and reseated the memory board and each memory module.
* Removed and reseated each processor and its associated power module.
* Removed and reseated each hard drive.
* Disabled the on-board video with configuration switch SW1(1) and tried using a PCI video card.
* Cleared the NVRAM with configuration switch SW1(6)
The LCD display remains the same at all times while the machine is plugged in, whether it's powered on or not. It reads:
COMPAQ LCD
Model # 56022
LCD FIRMWARE 1.9
The only thing I can think of to do now is start checking individual memory modules to see if one is bad. Any other suggestions?
* Removed and reseated the memory board and each memory module.
* Removed and reseated each processor and its associated power module.
* Removed and reseated each hard drive.
* Disabled the on-board video with configuration switch SW1(1) and tried using a PCI video card.
* Cleared the NVRAM with configuration switch SW1(6)
The LCD display remains the same at all times while the machine is plugged in, whether it's powered on or not. It reads:
COMPAQ LCD
Model # 56022
LCD FIRMWARE 1.9
The only thing I can think of to do now is start checking individual memory modules to see if one is bad. Any other suggestions?
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-02-2004 07:01 AM
06-02-2004 07:01 AM
Re: ProLiant 8500: No video or POST
Turned out it was a bad memory module. I pulled the DIMMs from one of the memory banks and it works fine now.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP