- Community Home
- >
- Servers and Operating Systems
- >
- ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- ProLiant DL388 Gen8 won't power on
-
-
Forums
- Products
- Servers and Operating Systems
- Storage
- Software
- Services
- HPE GreenLake
- Company
- Events
- Webinars
- Partner Solutions and Certifications
- Local Language
- China - 简体中文
- Japan - 日本語
- Korea - 한국어
- Taiwan - 繁體中文
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Latin America
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Blog, Poland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-19-2019 05:17 AM - last edited on 12-19-2019 08:04 AM by Parvez_AL
12-19-2019 05:17 AM - last edited on 12-19-2019 08:04 AM by Parvez_AL
ProLiant DL388 Gen8 won't power on
通电开机后过一段时间会进入待机状态,并且健康状态灯频闪红色,再按开机键无反应,硬盘指示灯不亮,已经检查过内存与电源,依然无法启动
检查过内存与电源,内存与电源都尝试更换过,但无效果,依然无法开机
Google Translated
After a period of time after power-on, it will enter the standby state, and the health status light flashes red. Pressing the power-on button has no response. The hard disk indicator is off. The memory and power have been checked. The power supply has been tried and replaced, but it has no effect and still cannot be turned on.
- Tags:
- ProLiant DL388e Gen8
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-19-2019 10:20 PM - edited 12-19-2019 10:21 PM
12-19-2019 10:20 PM - edited 12-19-2019 10:21 PM
Re: ProLiant DL388 Gen8 won't power on
Hello
1. Check by drain the server power by disconnecting all Power cables and hold the power button for 30 second.
2. Bring the server to bare minimum configuration and check the status.
i. A minimum of one Processor required per serve.
ii. Install DIMMs to corresponding processor installed
iii. Disconnect all the cable connected to server system board (hard drive back plane etc).
3. If still unable to isolate the issue, then refer Systems Insight Display LED combinations to isolate the issue.
HP ProLiant DL388p Gen8 Server User Guide (Page Number 11)
http://h20628.www2.hp.com/km-ext/kmcsdirect/emr_na-c03231404-2.pdf

Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2022 Hewlett Packard Enterprise Development LP