- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Problem of controler 6i with hp proliant DL38...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-06-2006 05:09 PM
тАО09-06-2006 05:09 PM
Trying to install a new DL 380 G with smart start, I get this error :
1776-SLOT 0 scsi bus terminator error.
And I could not install the the the Controler HP Smart Array 6i with is detected by the system.
So my system could not dectect any disk for installation
Thank you for your help
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-06-2006 07:14 PM
тАО09-06-2006 07:14 PM
SolutionThe SCSI bus is not properly terminated when internal and external drives are attached concurrently to the same SCSI bus.
The indicated SCSI bus is disabled until this problem is resolved.
Turn off the server power and check the cabling to the specified SCSI port.
Regards,
rmn
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2006 06:33 PM
тАО09-07-2006 06:33 PM
Re: Problem of controler 6i with hp proliant DL380 G4
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2006 08:00 PM
тАО09-07-2006 08:00 PM
Re: Problem of controler 6i with hp proliant DL380 G4
Are you using the BLUE "point to point" cable or the grey flat cable with a terminator?
You should be using the BLUE BLUE "point to point"
Rgds,
Roy
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2006 10:10 PM
тАО09-07-2006 10:10 PM
Re: Problem of controler 6i with hp proliant DL380 G4
I just verify the terminator.
My problem is du in the fact that the scsi bus is not terminated.
I have one terminator but after that another scsi bus start
Thank you for your help
KUZO