- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Problem with HP Proliant ML 350 G5 - after replaci...
ProLiant Servers (ML,DL,SL)
1753886
Members
7102
Online
108809
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-16-2011 11:49 AM
тАО02-16-2011 11:49 AM
Problem with HP Proliant ML 350 G5 - after replacing accelerator battery
I'm new so that i want to say hello to everyone.
I have a (maybe small) problem with my smart array e200i controller. Maybe someone met and solved it and could be please to help me. So that, I've got message that i need to replace my battery accelerator. OK i bought battery and replaced it. I read that i had waited 72h to fully recharge. OK it was at 1st february and to present day i need to reboot my srv. After reboot after POST i received again message "1794- Slot 1 Driver Array - Array Accelerator Battery charge Low
Array Accelerator Post-Write Cache is temporarily disabled." . Tomorrow i'll check version of firmware maybe i need to update or in the worst case it's a some fault with controller? If somebody could help me i would be appreciate. Thanx in advance! Greetings!
Matthew
I have a (maybe small) problem with my smart array e200i controller. Maybe someone met and solved it and could be please to help me. So that, I've got message that i need to replace my battery accelerator. OK i bought battery and replaced it. I read that i had waited 72h to fully recharge. OK it was at 1st february and to present day i need to reboot my srv. After reboot after POST i received again message "1794- Slot 1 Driver Array - Array Accelerator Battery charge Low
Array Accelerator Post-Write Cache is temporarily disabled." . Tomorrow i'll check version of firmware maybe i need to update or in the worst case it's a some fault with controller? If somebody could help me i would be appreciate. Thanx in advance! Greetings!
Matthew
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-17-2011 11:52 AM
тАО02-17-2011 11:52 AM
Re: Problem with HP Proliant ML 350 G5 - after replacing accelerator battery
Hello! We mostly have ML370 G4 servers and have found that upgrading the firmware resolved many failed battery messages. If the battery failed again after that, we replaced it. If you have two batteries on the card, you can switch them and see if the error "moves." If it doesn't, it is probably the card.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-17-2011 04:44 PM
тАО02-17-2011 04:44 PM
Re: Problem with HP Proliant ML 350 G5 - after replacing accelerator battery
The battery is attached to the cache module with a cable. Have you made sure to check that this cable is seated correctly? It's also possible that this cable may be damaged and the battery never gets charged due to this.
The truth is out there, but I forgot the URL..
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-18-2011 08:45 AM
тАО02-18-2011 08:45 AM
Re: Problem with HP Proliant ML 350 G5 - after replacing accelerator battery
Hello again! At first thnx for reply. I'm confused, battery doesn't have cable with connector to memory module. It only has + and - on bottom. Interesting thing is that memory module has a two pins but both batteries were attached by clips to memory module without used any cable connector. I noticed that battery reported in 2009 that was not fully charged. Maybe it's different installation and charging mode in ML 350 G5 without using any cable connectors or something is missing from the time when server was bought. It's really confusing me...
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP