- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Proliant 1850r
ProLiant Servers (ML,DL,SL)
1753428
Members
4838
Online
108793
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-05-2003 07:15 AM
тАО06-05-2003 07:15 AM
I cant get my server to boot to CD I have downloaded the System Config Utility but still cant get it to boot from Cd. I do have Smart Start 5.2 cd but I cant boot to it. Any ideas ??????
thanks
Micheal
thanks
Micheal
Nothing says out of the box will be easy
Solved! Go to Solution.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-05-2003 09:33 AM
тАО06-05-2003 09:33 AM
Solution
I would recommend clearing NVRAM on the machine. You can do this by opening the machine up, looking at approximately the front edge of the system board near the middle. You should see six switches in the switchbank. Turn switch 6 on, power the server up, turn it back off after the processors and memory are initialized, and turn the switch back off. This should reset it back to the factory defaults: floppy, cd, drive. If it still has a problem with booting from cd, then it's likely a problem with the drive.
The truth is out there, but I forgot the URL..
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-05-2003 11:59 AM
тАО06-05-2003 11:59 AM
Re: Proliant 1850r
Thanks for the help did as you said and rebooted and it loaded it booted from the CD and Im loading everything now.
Thanks again
Micheal
Thanks again
Micheal
Nothing says out of the box will be easy
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2003 07:33 AM
тАО06-06-2003 07:33 AM
Re: Proliant 1850r
This also works on the Proliant DL360 G1 servers.
Thanks for the post!
Thanks for the post!
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP