- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Proliant 350 ML G1
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-11-2010 12:56 PM
тАО01-11-2010 12:56 PM
The server tries to start up but only gets as far as initilizing all the fans for about 30 seconds and then turns off. It keeps retrying the procssess over and over until I turn the power off from the plug.
Any ideas?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-11-2010 01:10 PM
тАО01-11-2010 01:10 PM
Re: Proliant 350 ML G1
remove all pci cards and extra options
if only one psu put it in other slot ensure power from wall socket is good and cables secure
reseat all dims use min configuration
if issue persists logical option is to
disconnect all drives and controllers if issue still persists next logical and cheapest option is to replace the psu
This is how we thank each other in the forum
http://forums11.itrc.hp.com/service/forums/helptips.do?#33
Enjoy:)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2010 02:26 AM
тАО01-12-2010 02:26 AM
Re: Proliant 350 ML G1
Initializing fans, does that show up on the monitor or is it just that the fans start to spin and then they stop and then start again when the reboot happens?
If you get something on the monitor:
Does it always stop for example when it's trying to load the storage controller or so, that might give you a hint.
But as Mark wrote, running the server in minimal config is quite often a good way to start troubleshooting these kind of issues.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2010 05:24 AM
тАО01-12-2010 05:24 AM
Re: Proliant 350 ML G1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2010 06:36 AM
тАО01-12-2010 06:36 AM
Re: Proliant 350 ML G1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2010 06:38 AM
тАО01-12-2010 06:38 AM
Re: Proliant 350 ML G1
How many CPUs do you have? More than one? Try with only one. Can you try to move the PSU to the other slot if you only have one also?
Have you tried to clear the BIOS/NVRAM?
It's the DIP switch and DIP #2 that needs to be set to clear CMOS.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2010 07:34 AM
тАО01-12-2010 07:34 AM
Re: Proliant 350 ML G1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2010 07:44 AM
тАО01-12-2010 07:44 AM
SolutionThe card has the embedded NIC, storage controller, graphics card. Seems like an easy fix to try to replace that as it replaces most things.. but maybe instead of paying $400 it's more useful to get another server and then you'll have one with warranty.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2010 08:15 AM
тАО01-12-2010 08:15 AM