Proliant 360 G2 and SmartStart 6.00

[Eric Stéphan]

Hello,

I've upgraded smartstart 5.4 to 6.0 on a proliant G2 and I've got an error message in the windows event viewer : event 1010 Perflib :
The Collect Procedure for the "Tcpip" service in DLL "C:\WINNT\system32\Perfctrs.dll" generated an exception or returned an invalid status. Performance data returned by counter DLL will be not be returned in Perf Data Block. Exception or status code returned is DWORD 0.

Any idea ?

Thanks

Eric

[Mark Cloutier]

Dear Eric,
Please re-apply SP2 for W2K.
But do not reboot. Make sure to rerun SmartStart 6.0 and reinstall the drivers for the Array/SCSI controllers. SP2 might overwrite the drivers.

Mark

[Kretz]

Hello.

I've installed Windows 2000 with Smartstart 7.1 ! Since the installation in the application log of the server the same error message described above from eric appears. Should i do the same workaro

[Melinda Cooper]

We have six DL360, G2's four of them have W2K, SP3 and were built with Smartstart 6.0 and I'm getting the same error. Two DL360, G2's have W2K, SP2 and also built with Smartstart 6.0 and I'm not getting the event 1010 Perflib application error. I had a feeling it might have to do with the Broadcom Nic7780 that is in all six of these machines. So far I've not been able to resolve this problem. Did what the other person suggest work? I also heard that Compaq was working on a fix for this.

[Martin Aberg]

It's the new NIC's that causes the problem. Have had it verified with Compaq and Broadcom are working on a new driver. Probably ready late march.
All machines with NIC 7780 driver 2.75 are having the same problems. Both DL360 and DL580.

/Martin

[Steve Dolap]

I have an older Proliant 6400 with CPQ 3131 NIC and after updating all the drivers with SupportPaq 5.5 the perlib errors started to appear. So that shoots down the theory that it is only happening with the Broadcom NICs.

I've also noticed that when you install the WIN2K + SP2 without any Compaq drivers the log is clean. Once you run 5.5 and newer, the perflib errors start to appear.

I have about 10+ Proliant DL360 G2 servers which are all having the problems. I have G1 servers as well that have the same errors.

Anything that I upgrade with the newer CPQ drivers starts to display the error.

[Steve Dolap]

Correction to my last note. It's Win2k + SP3.

The 6400 has NT 4.0 + SP6a.

[David Howell_4]

I found another HP Resource Centre Reply.

This basically points the problem to a registry setting that disables performance counters for the tcpip service.

Set the following registry in your registry:

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Performance] "Disable Performance Counters"=dword:00000000


For the full story:

http://bizforums.itrc.hp.com/cm/QuestionAnswer/1,,0x28235bd3782dd711abdc0090277a778c,00.html


Regards,

Dave :o)

[Terry Hutchings]

MS is going to be releasing a KB article on this shortly, which will be Q318663. This will require getting a Pre-SP4 hotfix. I'd also recommend looking at Q186713 and looking at the second paragraph up from the bottom.

This issue may be able to be temporarily resolved by using SP20958.exe:
http://h18007.www1.hp.com/support/files/evoworkstation/us/download/14684.html
If you're planning on using teaming, then I wouldn't recommend using this driver.

[Steve Dolap]

I tried that disable performance counters fix and it doesn't work. just waiting on that pre-sp4 hotfix now.