- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Proliant DL580 booting
ProLiant Servers (ML,DL,SL)
1752221
Members
5410
Online
108785
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-28-2006 02:57 AM
тАО05-28-2006 02:57 AM
Proliant DL580 booting
Hello everyone, thanks for taking the time to read this. I just purchased a Proliant DL580 G1 to practice on, and when I was trying to install windows 2000 server after rebooting for the first time it just kept going back to the beggining, and started to install the op sys all over again. So I change the booting sequence on the SCSI to boot from cd, and now all I get is "system not found....." message. Now the system skips booting from a floppy or a CD, and it goes straight to the hard drive for the operating system. Can someone guide me as to how can I get this machine to boot again from floppy or cd? the hard drive is wipe clean, and I am not able to get to CMOS. any help will be greatly appreciated. Jose
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-28-2006 12:48 PM
тАО05-28-2006 12:48 PM
Re: Proliant DL580 booting
In DL580 G1, RBSU - F9.
In RBSU there are two settings:
1) > RBSU >Standard Boot Order (IPL)> Make CD-ROM to appear first in the list.
This would help you in getting booted from CD.
To avoid the OS re-installing all over again check with the boot controller order
> RBSU > Boot Controller Order > Ctrl:1 PCI Embedded HP Smart Array 6i
Ensure that the correct smart array controller is selected
Once you are done with the installation of the operating system you could change the boot order again
I hope this helps you
regards
Divakar
In RBSU there are two settings:
1) > RBSU >Standard Boot Order (IPL)> Make CD-ROM to appear first in the list.
This would help you in getting booted from CD.
To avoid the OS re-installing all over again check with the boot controller order
> RBSU > Boot Controller Order > Ctrl:1 PCI Embedded HP Smart Array 6i
Ensure that the correct smart array controller is selected
Once you are done with the installation of the operating system you could change the boot order again
I hope this helps you
regards
Divakar
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-28-2006 02:37 PM
тАО05-28-2006 02:37 PM
Re: Proliant DL580 booting
Thanks for your help but pressing the F9 or Control key does not acomplish anything. as the machine goes through posting it gets to where the SCSI array start to initialize I can press F8 to enter SCSI set up, I can't change the the boot procedure eventhough that's where I changed it to boot from hard drive. If I ESC to exit it just to where it says no system disk found or disk error. So I'm really not sure as to what's going on. Thanks so much Jose
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-28-2006 03:42 PM
тАО05-28-2006 03:42 PM
Re: Proliant DL580 booting
Would u have load defaults or set-defaults options in SCSI Bios, You could propably tru that.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP