- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Proliant DL580G2 & RA4100 Storage Array
ProLiant Servers (ML,DL,SL)
1753877
Members
7566
Online
108809
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-31-2004 02:03 AM
тАО03-31-2004 02:03 AM
Proliant DL580G2 & RA4100 Storage Array
Can you configure 2 DL580G2 to use a RA4100 Storage array without the two server being clustered, because I can only get one to connect at a time?
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-31-2004 03:23 AM
тАО03-31-2004 03:23 AM
Re: Proliant DL580G2 & RA4100 Storage Array
This should be no problem. However, the 2 servers must not be trying to access the same LUNs within the RA4100. Each server will have its own LUNs, and you should not configure them so that both servers are trying to share the same LUN (it's not supported and you'll corrupt your data).
What you need to do is set up Selective Storage Presentation (SSP). This is what assigns LUN access rights to servers.
Check out chapter 5 in this User Guide for help.
ftp://ftp.compaq.com/pub/products/storageworks/techdoc/raidstorage/146297e4.pdf
Thanks,
Doug
What you need to do is set up Selective Storage Presentation (SSP). This is what assigns LUN access rights to servers.
Check out chapter 5 in this User Guide for help.
ftp://ftp.compaq.com/pub/products/storageworks/techdoc/raidstorage/146297e4.pdf
Thanks,
Doug
I am an HPE employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-31-2004 03:28 AM
тАО03-31-2004 03:28 AM
Re: Proliant DL580G2 & RA4100 Storage Array
Thanks Doug this is very helpful.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP