- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Proliant ML150 smart drive failure
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-08-2011 06:34 AM
08-08-2011 06:34 AM
Re: Proliant ML150 smart drive failure
OK, this is a Proliant ML150, but is it ML150 G3, ML150 G5 or ML150 G6?
According to the image you posted, you have 2 disks, not 3. (The boot screen mentions disk #02 twice, first in a standard informational listing, then inside the WARNING: message.)
The disk in SATA port #02 (with serial number GB0500EAFJH) indicates SMART failure, i.e. its internal diagnostics indicates it will fail soon, but it may not have actually failed yet. Even so, if the OS still runs, you should immediately make a full backup and start the process for getting a new disk for this system.
The disk in SATA port #00 is OK.
The image you posted does not indicate the presence of any RAID sets at all: since the disks are not the same size, it is possible they are not configured for RAID at all: they might be used as stand-alone disks. From the image only, it is impossible to know if the RAID features are used at all or not.
You should verify your RAID configuration. Your OS should still be bootable by pressing Enter when you are at the boot screen.
Here's the Embedded SATA RAID User Guide.
Pages 9-13 describe the HRCONF command-line utility: please use it to display the RAID configuration and paste the output to this thread.
hrconf getconfig 0 AL hrconf getconfig 0 AL >raidconfig.txt
The first command line should display the RAID configuration in the command prompt window; the second should produce a raidconfig.txt file that contains the same information.
If you don't have this tool installed, see http://www.hp.com/go/sataraid
If it turns out you have two configured arrays with 1 disk each, that is not a fault-tolerant RAID1 configuration: however, it might still be possible to add another disk to the system, add it as a hotspare for the disk in port #02, and then begin a rebuild (= copy all data from the disk in port #02 to the new disk). The instructions for that are in the User Guide linked above: see pages 7 and 8.
If both disks belong to the same RAID set, the situation is not quite so critical: in this case, the other disk contains a 100% healthy copy of your data, so you'll only need to replace the failing disk and rebuild the array.
- « Previous
-
- 1
- 2
- Next »