- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Proliant ML330 G3 - Removing the Case
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-22-2004 11:46 PM
тАО07-22-2004 11:46 PM
We are a small company who puchased above server about a year ago. We have since purchased RAM to install and improve the performance. However we cannot seem to understand how one is supposed to remove the case. The side panels do not seem to be screwed in, but they don't seem to slide either.
I have attached pictures, sorry for the poor quality, taken on my v600.
If anyone can help, would be much appreaciated.
Kind regards,
Kevin
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-22-2004 11:53 PM
тАО07-22-2004 11:53 PM
Re: Proliant ML330 G3 - Removing the Case
did you try to remove the front pannel, there should be some screws to remove the side pannel.
Hope this helps!
Markus
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-23-2004 12:14 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-23-2004 12:45 AM
тАО07-23-2004 12:45 AM
Re: Proliant ML330 G3 - Removing the Case
Having identified the front as being point of access, it was a piece of cake. There was just a single screw to remove and the panel just slid off.
Thanks once again
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-23-2004 04:12 AM
тАО07-23-2004 04:12 AM
Re: Proliant ML330 G3 - Removing the Case
If you find answers useful, could you please assign points, depeding on how useful the info was?
Have a look here:
http://forums1.itrc.hp.com/service/forums/helptips.do?#33
Thanks, and happy upgrading!
Regards,
Stephen