- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Recover raid 0+1
ProLiant Servers (ML,DL,SL)
1753548
Members
5438
Online
108795
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-08-2007 11:30 PM
11-08-2007 11:30 PM
Recover raid 0+1
Hi,
I have hot swap 4 disk in raid 0+1 to change with other disks on a MSA 500. Because i don't have two files backed up i need to recover the old raid 0+1 volume. When i put the disk in the msa in same possition, the msa detect new disk and don't detect the old volume. Can i force with a smart array controller the rebuild of the raid, or can i have others forms to recover a lost raid 0+1 volume.
Tanks
I have hot swap 4 disk in raid 0+1 to change with other disks on a MSA 500. Because i don't have two files backed up i need to recover the old raid 0+1 volume. When i put the disk in the msa in same possition, the msa detect new disk and don't detect the old volume. Can i force with a smart array controller the rebuild of the raid, or can i have others forms to recover a lost raid 0+1 volume.
Tanks
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-09-2007 04:57 AM
11-09-2007 04:57 AM
Re: Recover raid 0+1
When you swapped the new 4 disks, you would have created a new array with RAID 0+1.
Since you had the same RAID configuration with the 4 older hard drives, the data would be intact, but since the volume is not recognized by MSA, you will need to configure the array with exact same settings. If all goes well, and if the drives are NOT re-initialized you will have your old volume back. This is a risky option as the drives contain valid data.
Since you had the same RAID configuration with the 4 older hard drives, the data would be intact, but since the volume is not recognized by MSA, you will need to configure the array with exact same settings. If all goes well, and if the drives are NOT re-initialized you will have your old volume back. This is a risky option as the drives contain valid data.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP