- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Replacing failed hard drive on HP ProLiant ML350 G...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-21-2009 08:19 AM
тАО07-21-2009 08:19 AM
Replacing failed hard drive on HP ProLiant ML350 G3
I have managed to source a new hard drive which is the same spec as the failed one. Would any one be able to offer some advice on the best way to go about replacing the failed one.
The hard drive will be one of three in a raid 5 configuration.
From my understanding the best way to carry this out would be to shut down the server and replace the failed one and then reboot and the system will recognise the new one and start the rebuild?
Any help would be great!
Thanks
Steven
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-21-2009 08:29 AM
тАО07-21-2009 08:29 AM
Re: Replacing failed hard drive on HP ProLiant ML350 G3
Thanks
Steven
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-21-2009 09:05 AM
тАО07-21-2009 09:05 AM
Re: Replacing failed hard drive on HP ProLiant ML350 G3
if they are hot swap drives you should be able to replace it online, the controller should automatically start the rebuild once it picks up the replacement drive, make sure you take a backup before you start (just in case)
which raid controller do you have installed ?
the rebuild will take some time depending on the size of the disks involved, if server activity can be kept to a minimum while the rebuild takes place this would help, all the drives will be pretty busy at this time and if you're going to get another disk fail it's usually at this time (which is where your earlier backup comes in !)
hth
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-22-2009 12:54 AM
тАО07-22-2009 12:54 AM
Re: Replacing failed hard drive on HP ProLiant ML350 G3
Thanks for the reply,
I have a smart array 641 controller installed on the server.
I was planning on carrying out the swap over the weekend so that the server is not in use and hopefully reduce the likelihood of another fail.
Thanks for the information so far are you aware of any documentation available which I could use as a back up?
Thanks
Steven
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-23-2009 01:10 PM
тАО07-23-2009 01:10 PM