- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- SmartStart 7.60, BL35p, and Windows Server 2003 R2
ProLiant Servers (ML,DL,SL)
1753261
Members
5015
Online
108792
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-20-2006 02:12 AM
тАО10-20-2006 02:12 AM
SmartStart 7.60, BL35p, and Windows Server 2003 R2
Hello,
I'm trying to install Windows Server 2003 R2 on one of my BL35p blades. I was using SmartStart 7.51, but it kept giving errors so I switched to 7.60. Now, I get past the stage where I provide my CD Key and such.
I'm at a screen that says "Preparing Drive for Operating System Installation..." Below this are three tasks:
* Erasing...
* Creating Partition
* Copying Drivers and Proliant Support Pack
It has been on this screen for about an hour now. There is disk and network activity and the Advertisement is cylcing on the page.
This is over a 100Mbps link to iLO. Should it take this long?
Thanks,
Dean
I'm trying to install Windows Server 2003 R2 on one of my BL35p blades. I was using SmartStart 7.51, but it kept giving errors so I switched to 7.60. Now, I get past the stage where I provide my CD Key and such.
I'm at a screen that says "Preparing Drive for Operating System Installation..." Below this are three tasks:
* Erasing...
* Creating Partition
* Copying Drivers and Proliant Support Pack
It has been on this screen for about an hour now. There is disk and network activity and the Advertisement is cylcing on the page.
This is over a 100Mbps link to iLO. Should it take this long?
Thanks,
Dean
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-20-2006 05:30 AM
тАО10-20-2006 05:30 AM
Re: SmartStart 7.60, BL35p, and Windows Server 2003 R2
Ok... so I stopped this process, updated the ILO firmware, and tried again. It only sat at the screen about 10 minutes this time and then asked for the OS media. I should be fine.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-22-2006 05:50 AM
тАО10-22-2006 05:50 AM
Re: SmartStart 7.60, BL35p, and Windows Server 2003 R2
The OS is now installed fine. The firmware upgrade worked.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP