- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- UPS Shuts off when trying to boot with serial cabl...
ProLiant Servers (ML,DL,SL)
1753521
Members
5549
Online
108795
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-23-2001 04:00 PM
тАО04-23-2001 04:00 PM
UPS Shuts off when trying to boot with serial cable connected
Server will not boot when communication cable is connected, if cable not connected, all works well. Took another Prolient 2500 server and connected its communication cable to the same UPS and it worked fine, so I know it is the Prolient 3000 that is sending some signal to the UPS to not start. Any ideas ??
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-26-2001 04:00 PM
тАО04-26-2001 04:00 PM
Re: UPS Shuts off when trying to boot with serial cable connected
What type of UPS is connected? Is the UPS operating in battery mode during boot-up? Are there any power to the led on the front of the Server unit? If the UPS is a Compaq UPS, then a Compaq special serial cable should be used. No third party cable. Check the voltage from the UPS. Check the minimum voltage requirements for the server in question. If the actual voltage is less than the minimum supported voltage, the problem is with the UPS.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-27-2001 04:00 PM
тАО06-27-2001 04:00 PM
Re: UPS Shuts off when trying to boot with serial cable connected
We have a Proliant 3000 and an APC smart-UPS. This would trip into run calibration mode on restart. I found that boot.ini needed /noserialmice added to it as the com port was sending a signal on startup which triggered the UPS
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP