- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- dl360gen9 ilo no ip and both led green
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-12-2021 07:40 AM
05-12-2021 07:40 AM
dl360gen9 ilo no ip and both led green
Hello together,
i have a dl360gen9 server who is getting no ilo ip...
ilo was resetted, but no luck. another server worked fine!
on the ilo interface both leds are permanently on ?!
on the second server the leds are out and only on, if cable was connected...
Any Ideas?
Thanks...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-12-2021 08:21 PM
05-12-2021 08:21 PM
Re: dl360gen9 ilo no ip and both led green
Hello,
Here are few troubleshooting steps which might help you to resolve this issue : https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&docId=emr_na-a00045659en_us#N100C5
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-16-2021 08:32 PM - edited 05-16-2021 08:34 PM
05-16-2021 08:32 PM - edited 05-16-2021 08:34 PM
Re: dl360gen9 ilo no ip and both led green
1. Check by cold/hard reboot of the server.
2. Power drain the server and check the status.
Steps To Power drain the server:
i. Remove both power cables.
ii. Press and hold power button without connecting power cables.
iii. Later release power button and connect power cables and power on the server.
3. Clear NVRAM
Following are steps to clear NVRAM using the system maintenance switch on the system board:
a. Extend the server from the rack, remove the access panel, and locate the system maintenance switch (refer to item 1 in figure 1 below).
b. Move switch S6 from default 'Off' position to 'On', install the access panel and connect the power cable to the walljack and power it on.
c. When a message indicates that a maintenance switch has been turned on and the unit has been reset, power it off, remove the power cable from the walljack. Remove it from the rack, remove the access panel and reverse switch S6 to 'Off' and then power the server back again.
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]