- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- how to set lo ip address using cli for hp dl 180 g...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-08-2010 11:55 AM
тАО08-08-2010 11:55 AM
how to set lo ip address using cli for hp dl 180 g6 having lights out 100
how to set lights out 100 ip address using cli for hp dl 180 g6
hponcfg gives error as
hponcfg
HPONCFG RILOE II/iLO setup and configuration utility
Version 1.9 (c) Hewlett-Packard Company, 2008
ERROR: A general system error occurred while detecting iLO/RILOE-II.
ACTION REQUIRED: Check if iLO and iLO driver is up and running.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-08-2010 05:29 PM
тАО08-08-2010 05:29 PM
Re: how to set lo ip address using cli for hp dl 180 g6 having lights out 100
Press the F8 key when prompted during POST. The iLO RBSU runs
You can also, try updatinig the firmware for the ilo.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-08-2010 10:56 PM
тАО08-08-2010 10:56 PM
Re: how to set lo ip address using cli for hp dl 180 g6 having lights out 100
Are you certain that this card is supported with this utility?
(I believe the ILO 100 series is 'special')
If it doesn't get an address using DHCP, you may need to reboot your server and enter its BIOs setup( press [F10] during POST)
and enter it there.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-10-2010 01:08 AM
тАО08-10-2010 01:08 AM
Re: how to set lo ip address using cli for hp dl 180 g6 having lights out 100
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-10-2010 01:31 AM
тАО08-10-2010 01:31 AM
Re: how to set lo ip address using cli for hp dl 180 g6 having lights out 100
(Check the list of leases on the nearest DHCP-server for anything beginning with ILO... )
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-10-2010 08:30 AM
тАО08-10-2010 08:30 AM
Re: how to set lo ip address using cli for hp dl 180 g6 having lights out 100
Have you installed the iLO Interface Management driver and the iLO Management Controller driver?
good luck, if you appreciate the answers we appreciate the points!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-10-2010 11:47 AM
тАО08-10-2010 11:47 AM
Re: how to set lo ip address using cli for hp dl 180 g6 having lights out 100
thanks for the reply..we want to assign static ip to the lo100. We want to do it online (when it is live with os )and not while server boots.
hponcfg utility is there for online configuration of ilo2 on dl580 servers..like that is there any utility for lo100 for hp dl 180 g6servers for accessing lo100 through os directly to change configuration?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-10-2010 12:43 PM
тАО08-10-2010 12:43 PM
Re: how to set lo ip address using cli for hp dl 180 g6 having lights out 100
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-13-2010 11:18 PM
тАО08-13-2010 11:18 PM