- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- hp blade and GBE 2 switch
ProLiant Servers (ML,DL,SL)
1753762
Members
4801
Online
108799
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-03-2006 01:00 AM
07-03-2006 01:00 AM
hp blade and GBE 2 switch
we install hp blade enclosure with 8 servers bl20 g3
the network config :
** left side connected to cisco core switch A
port 17,18 trunk 1 stp enabled
port 19,20,21,22 trunk 2 stp enabled
** right side connected to cisco core switch b
port 17,18 trunk 1 stp enabled
port 19,20,21,22 trunk 2 stp enabled
when I unplug GBE sw and add SAN connectivity KIT
my network stop response
and there is a loop hapened because the GBE SW unplug and replug it lost all configurations specially trunk so loop happend
because port 19,20,21,22 connected to cisco core switch with ether chanel
why configuration losted..??
....
thanks
the network config :
** left side connected to cisco core switch A
port 17,18 trunk 1 stp enabled
port 19,20,21,22 trunk 2 stp enabled
** right side connected to cisco core switch b
port 17,18 trunk 1 stp enabled
port 19,20,21,22 trunk 2 stp enabled
when I unplug GBE sw and add SAN connectivity KIT
my network stop response
and there is a loop hapened because the GBE SW unplug and replug it lost all configurations specially trunk so loop happend
because port 19,20,21,22 connected to cisco core switch with ether chanel
why configuration losted..??
....
thanks
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-03-2006 05:48 AM
07-03-2006 05:48 AM
Re: hp blade and GBE 2 switch
firmware ? for GBE2
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP