Skip to ContentSkip to Footer
Start of content
- Community Home
- >
- Servers and Operating Systems
- >
- ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- hpacucli broken on E200i
ProLiant Servers (ML,DL,SL)
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
-
- Forums
-
Blogs
- Alliances
- Around the Storage Block
- Behind the scenes @ Labs
- HPE Careers
- HPE Storage Tech Insiders
- Infrastructure Insights
- Inspiring Progress
- Internet of Things (IoT)
- My Learning Certification
- OEM Solutions
- Servers: The Right Compute
- Shifting to Software-Defined
- Telecom IQ
- Transforming IT
- Infrastructure Solutions German
- L’Avenir de l’IT
- IT e Trasformazione Digitale
- Enterprise Topics
- ИТ для нового стиля бизнеса
- Blogs
-
Quick Links
- Community
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Contact
- Email us
- Tell us what you think
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Enterprise.nxt
- Marketplace
- Aruba Airheads Community
-
Forums
-
Blogs
-
InformationEnglish
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
10-01-2007 11:18 PM
10-01-2007 11:18 PM
hpacucli broken on E200i
Testing hpacucli-7.85-18 with RHEL4u5 i386 on a DL360 G5 with onboard E200i SAS controller, it appears that the serialnumber= syntax is broken.
[root@lthlha98 ~]# uname -r
2.6.9-55.0.2.ELsmp
[root@lthlha98 ~]# hpacucli ctrl all shot
Error: Invalid command. Type "help" for a list of valid commands.
[root@lthlha98 ~]# hpacucli ctrl all show
Smart Array E200i in Slot 0 (sn: PR77MU4754 )
[root@lthlha98 ~]# hpacucli ctrl sn=PR77MU4754 show
Error: The controller identified by "serialnumber=pr77mu4754" was not detected.
[root@lthlha98 ~]# hpacucli ctrl slot=0 show
Smart Array E200i in Slot 0
Bus Interface: PCI
Slot: 0
Serial Number: PR77MU4754
RAID 6 (ADG) Status: Disabled
Controller Status: OK
Chassis Slot:
Hardware Revision: Rev A
Firmware Version: 1.66
Rebuild Priority: Medium
Expand Priority: Medium
Surface Scan Delay: 15 sec
Cache Board Present: True
Cache Status: OK
Accelerator Ratio: 100% Read / 0% Write
Total Cache Size: 64 MB
Battery Pack Count: 0
[root@lthlha98 ~]#
I've tried earlier versions of hpacucli (namely 7.70-12 and 7.80-6) but these both suffer the same problem.
I've separately managed to verify that 7.70-12 works OK with a P400 so I've speculating this is an issue with the cciss driver or the E200i itself.
Is this a known issue (and if so, is there is fix in the pipeline)?
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
End of content
United States
Hewlett Packard Enterprise International
Communities
- Communities
- HPE Blogs and Forum
© Copyright 2019 Hewlett Packard Enterprise Development LP