- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- integrated smart array controller
ProLiant Servers (ML,DL,SL)
1753907
Members
8655
Online
108810
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-18-2000 04:00 PM
12-18-2000 04:00 PM
integrated smart array controller
I am installing Microsoft TSE on a dl580 with 2.5 gig of memory
and 4 700mhz proceesors, with a internal smart array controller
when I use the ssd for nt version 2.18A off of 4.80 smart start,
I have tried to use the array controller for windows nt, but it says there is no card. when I use the integrated smart array for 42xx and 43xx the driver loads and then says there is no hard drive.
is there a special driver for this board? this is the first time I have worked with it.
thanks
D
and 4 700mhz proceesors, with a internal smart array controller
when I use the ssd for nt version 2.18A off of 4.80 smart start,
I have tried to use the array controller for windows nt, but it says there is no card. when I use the integrated smart array for 42xx and 43xx the driver loads and then says there is no hard drive.
is there a special driver for this board? this is the first time I have worked with it.
thanks
D
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-26-2000 04:00 PM
12-26-2000 04:00 PM
Re: integrated smart array controller
In order to install NT on a system with a current Compaq Array controller, you need to create the 3 NT install disks from the NT CD. Use the "WINNT /OX" command to do this. Then, when the Smartstart manual install is done, boot from those disks - without the NT CD in the drive until asked. Choose "custom" for the install mode (F6 key) and skip detection on mass storage. Specify an unlisted controller and use the Compaq NT 4.0 SSD for the drivers (in this case, the "Integrated" driver). Then specify a secondary controller and use the NT "IDE/Atapi" driver. You can also use the SSD for the NIC drivers (also likely to be out of date in NT).
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP