Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2008 05:44 AM
тАО02-15-2008 05:44 AM
ml150 g3
regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2008 05:53 AM
тАО02-15-2008 05:53 AM
Re: ml150 g3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2008 06:01 AM
тАО02-15-2008 06:01 AM
Re: ml150 g3
Regards.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2008 06:12 AM
тАО02-15-2008 06:12 AM
Re: ml150 g3
You need to press F6 at the beggining of the Windows CD boot and provide it the driver for the controller.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2008 06:19 AM
тАО02-15-2008 06:19 AM
Re: ml150 g3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2008 06:24 AM
тАО02-15-2008 06:24 AM
Re: ml150 g3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2008 06:50 PM
тАО02-15-2008 06:50 PM
Re: ml150 g3
damien this is not a good answer but do a research for ml150 g3 or nlite you're going to get a lof results on this stuff and the procedures to install that box.
- USB floppy / HP Branded
- nlite
regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2008 06:53 PM
тАО02-15-2008 06:53 PM
Re: ml150 g3
Check this out:
Follow the steps below and there is no need to use Floppy Drive or a Slipstreaming OS CD:
1.
Install the OS with Embedded SATA RAID Disabled (No Drivers or F6 required) on one Harddrive.
2.
Once OS is installed, Extract the Embedded SATA RAID Drivers to a folder. HP Embedded SATA RAID Controller Driver for Windows 2000/Windows Server 2003:
3.
Go to Control Panel-> Add New Hardware->Device is connected->New Hardware->Raid Controller->Have Disk->Browse to the folder where the Embedded SATA RAID Drivers were extracted. Select the .inf file->Install Adaptec Raid Driver.
4.
Restart the Server go to BIOS enable the Embedded SATA RAID.
5.
Press F8 and go to Sata Raid BIOS->Configure the Drives->Create Array->Raid 0/1 A warning message will appear "Warning: Configuring the drives will erase all Array information from the selected drives, if that drive is part of an array. Arrays using any of these drives as members will be affected! Do you want to continue?(Yes/No):". Press "Y" to continue.
6.
If Raid 1 is selected it will ask you what is the Source Disk, select the Right Disk in which OS was installed previously. Warning message might appear again. Select "Y".
7.
Rebuild will take sometime, once rebuild is complete restart the server.
Once rebooted Raid would be detected and windows would boot up, in windows it would detect new hardware and Adaptec Raid drivers will be installed. Now Server is built migrated to Raid Successfully.
regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-18-2008 07:26 AM
тАО02-18-2008 07:26 AM
Re: ml150 g3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-18-2008 06:46 PM
тАО02-18-2008 06:46 PM
Re: ml150 g3
yes you enable/disable SATA from BIOS
regards