- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- ml350 g4 will not boot from ADS pushed image
ProLiant Servers (ML,DL,SL)
1753544
Members
5878
Online
108795
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-16-2004 12:39 PM
11-16-2004 12:39 PM
ml350 g4 will not boot from ADS pushed image
We are using Microsoft Automated Deployment Services (ADS).
We have several of each
ML350 G2, G3, G4
When I deploy an imaage with ADS, the new drive will boot on G2 and G3 boxes, but NOT G4.
Even if the image was captured from a G4, and then pushed right back to the same G4 and drive, it will not boot on a G4, only the G2 and G3.
During the boot process, when it gets to "Attempting to boot from hard drive C:" prompt, it just hangs there forever.
Again, I know that the drive image is just fine because it will boot onto the G2 and G3 boxes just fine.
Any ideas?
Thanks,
Robert
We have several of each
ML350 G2, G3, G4
When I deploy an imaage with ADS, the new drive will boot on G2 and G3 boxes, but NOT G4.
Even if the image was captured from a G4, and then pushed right back to the same G4 and drive, it will not boot on a G4, only the G2 and G3.
During the boot process, when it gets to "Attempting to boot from hard drive C:" prompt, it just hangs there forever.
Again, I know that the drive image is just fine because it will boot onto the G2 and G3 boxes just fine.
Any ideas?
Thanks,
Robert
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-28-2004 02:51 PM
11-28-2004 02:51 PM
Re: ml350 g4 will not boot from ADS pushed image
This may be related to the issue with DL380 G4's.
Have a look at this thread.
http://forums1.itrc.hp.com/service/forums/bizsupport/questionanswer.do?admit=716493758+1101699507126+28353475&threadId=707961
Have a look at this thread.
http://forums1.itrc.hp.com/service/forums/bizsupport/questionanswer.do?admit=716493758+1101699507126+28353475&threadId=707961
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP