- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: modify raid 1 array from SMH or OS?
ProLiant Servers (ML,DL,SL)
1754014
Members
7378
Online
108811
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-22-2007 01:30 PM
тАО10-22-2007 01:30 PM
modify raid 1 array from SMH or OS?
I want to replace the hard drives in a RAID 1 mirror on a DL385 running CentOS 4.3. I don't see any action other than 'identify drive' on the System Management Homepage storage section. Ideally I would just remove one of the physical drives and replace it, the controller would rebuild the array, and then I'd do the same with the second drive. But when I insert the replacement drive it faults. How do I use a utility to force a mirror rebuild using the new drive?
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-22-2007 03:13 PM
тАО10-22-2007 03:13 PM
Re: modify raid 1 array from SMH or OS?
You're looking for the Array Configuration Utility. It needs to be setup for local or remote use, and if enabled for remote will be linked from the SMH.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-22-2007 06:25 PM
тАО10-22-2007 06:25 PM
Re: modify raid 1 array from SMH or OS?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-23-2007 01:26 PM
тАО10-23-2007 01:26 PM
Re: modify raid 1 array from SMH or OS?
Thanks guys, I started the acu -R and lo it did appear. -F
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP