- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: new SA 6402 on Proliant 350ML G3
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-01-2006 03:33 AM
тАО09-01-2006 03:33 AM
new SA 6402 on Proliant 350ML G3
I just bought 6402 to improve my server and I cannot get that working. Immediately after start, it says 1783 - Adapter slot.... is in lockup state due to hardware configuration error.
I have managed after couple of restarts to upgrade the firmware of the disks and of 6402 as well, but it still behaves like that.
Any ideas what to do next are welcome.
Thanks,
Connyas
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-01-2006 03:41 AM
тАО09-01-2006 03:41 AM
Re: new SA 6402 on Proliant 350ML G3
If there is a array accelarator module,take it out or reseat it and check if server boots ok.
SRH
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-01-2006 03:47 AM
тАО09-01-2006 03:47 AM
Re: new SA 6402 on Proliant 350ML G3
If this message appears immediately following a ROM installation, the ROM is defective or not installed properly.
Check that the controller is firmly inserted in its slot.
Check for improper cabling or SCSI ID conflicts.
Try upgrading the System ROMs from here:
http://h18023.www1.hp.com/support/files/server/us/download/22051.html
Hope this works!!!!
Regards,
rmn
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-01-2006 04:08 AM
тАО09-01-2006 04:08 AM
Re: new SA 6402 on Proliant 350ML G3
tried to re-insert, even moved to another slot. After first power-up it works, even the OS comes up. When I restart the server or power cycle him, the same message comes up again.
Please, do you have any ideas left?
Thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-01-2006 09:18 PM
тАО09-01-2006 09:18 PM
Re: new SA 6402 on Proliant 350ML G3
Install a hot-plug point to point cable from the 6402 to the SCSI backplane and 1783's should go away.
Only use a hot-plug point to point cable when attaching a Smart Array to a self terminating hot-plug SCSI backplane.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-02-2006 02:00 AM
тАО09-02-2006 02:00 AM
Re: new SA 6402 on Proliant 350ML G3
1-Reseat the SA6400 and cables.
2-Remove the BBWC
3-Clear the NVRAM
4-Upgrade the sysRom using this link: http://h18023.www1.hp.com/support/files/server/us/download/22051.html
5-Upgrade the firmware of the controller using this link: http://h18023.www1.hp.com/support/files/server/us/download/24943.html