- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- uniprocessor to multiprocessor
ProLiant Servers (ML,DL,SL)
1753971
Members
8171
Online
108811
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2001 04:00 PM
тАО02-14-2001 04:00 PM
uniprocessor to multiprocessor
How do I get NT to recognize the second processor that I just added?
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-01-2001 04:00 PM
тАО03-01-2001 04:00 PM
Re: uniprocessor to multiprocessor
follow the instructions in the SSD help file for HAL upgrade. BUT DO NOT REBOOT BEFORE REAPPLYING SERVICE PACK. This is VERY important.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2001 04:00 PM
тАО04-03-2001 04:00 PM
Re: uniprocessor to multiprocessor
Thank you penners for your help .....
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2001 04:00 PM
тАО04-03-2001 04:00 PM
Re: uniprocessor to multiprocessor
Install the new processor(s) as noted in the manual for the system itself or that comes with the chips.
Then configure the server hardware to the correct the "APIC Mode" settings. You must start System Configuration and press 'CTRL a' at the first menu after selecting F10 during boot. This activates "Advanced Mode". Then enter System Configuration itself and follow the prompts to complete a basic configuration load. Select to "Review" the settings and then pick "View/Edit Details" from the menu. Look down the list to find "APIC Mode". Press enter on this selection and select "Full Table, Mapped" (or "Full Table" if only choice, depends on specific system). Once this has been done, exit and save changes.
The next step is to load the Multiprocessor HAL on NT. This is best accomplished with the latest Compaq NT SSD (for 3.51 or 4.0 specifically) as this utility will do a more reliable job of identifying the correct HAL for the system. Simply run SETUP.EXE from the SSD disk 1 and select the HAL upgrade (you may also install other drivers if desired, do NOT force all drivers to load as some may not work on your system).
Then configure the server hardware to the correct the "APIC Mode" settings. You must start System Configuration and press 'CTRL a' at the first menu after selecting F10 during boot. This activates "Advanced Mode". Then enter System Configuration itself and follow the prompts to complete a basic configuration load. Select to "Review" the settings and then pick "View/Edit Details" from the menu. Look down the list to find "APIC Mode". Press enter on this selection and select "Full Table, Mapped" (or "Full Table" if only choice, depends on specific system). Once this has been done, exit and save changes.
The next step is to load the Multiprocessor HAL on NT. This is best accomplished with the latest Compaq NT SSD (for 3.51 or 4.0 specifically) as this utility will do a more reliable job of identifying the correct HAL for the system. Simply run SETUP.EXE from the SSD disk 1 and select the HAL upgrade (you may also install other drivers if desired, do NOT force all drivers to load as some may not work on your system).
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP