- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- Re: Adding an Autoloader External Tape Drive to a ...
ProLiant Servers - Netservers
1753331
Members
5088
Online
108792
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-20-2005 05:06 AM
тАО12-20-2005 05:06 AM
Adding an Autoloader External Tape Drive to a Proliant ML350
We have hooked up a Quantum Superloader 3 to one of the SCSI ports on the Compaq 64-bit Wide Ultra3 SCSI adapter, but it only detects the Tape Drive and not the Autoloader. This is a multi-Lun device, so should the controller just detect this, or is there a setting somewhere that I can change? Does it matter which SCSI port it is plugged into? I ran the SmartStart CD but it didn't seem to have any configurable settings.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-22-2005 06:11 PM
тАО12-22-2005 06:11 PM
Re: Adding an Autoloader External Tape Drive to a Proliant ML350
I have this problem with HP DL380G3 & Autoloader HP SSL1016. HP SSL1016 was plugged into SCSI port on HP DL380, but it only detects the Tape Drive. I inserted Compaq SCSI Card (with 2 SCSI ports) into PCI-X slot. Plug HP SSL1016 into Compaq SCSI card and after system detect Tape Drive & Autoloader :)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-22-2005 08:04 PM
тАО12-22-2005 08:04 PM
Re: Adding an Autoloader External Tape Drive to a Proliant ML350
Aleksey, DL380 external SCSI port is port of RAID controller and it cannot be attached to autoloader.
But Randall use simple SCSI card. This SCSI card must support LUN adressing mode, I'm not sure does such support exist in Compaq 64-bit Wide Ultra3 SCSI adapter.
But Randall use simple SCSI card. This SCSI card must support LUN adressing mode, I'm not sure does such support exist in Compaq 64-bit Wide Ultra3 SCSI adapter.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP