- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- Re: BIOS feature request for ML110 G5
ProLiant Servers - Netservers
1748086
Members
4937
Online
108758
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-26-2008 03:37 AM
03-26-2008 03:37 AM
BIOS feature request for ML110 G5
Hi.
I am not sure if this is the right place to post this request but I hope someone from HP will be able to pick this up.
We have a number of ML110 G5 servers which we would like to be able to boot from an HDD attached to SATA port 5 or 6. This was possible with the G4 version of the server (using the PATA ports), but on the G5, these ports are "forcibly" detected as CDROM's by the BIOS as soon as SATA RAID is enabled on the other ports (1-4). This means that the BIOS cannot boot from this device.
The drive is detected correctly in F10 Setup using AUTO or USER, but as soon as the server reboots it is reset to CDROM.
Does anyone have a workaround to allow this, or would HP consider a BIOS update to allow this setting to be retained over a reboot?
Many Thanks,
Nick.
I am not sure if this is the right place to post this request but I hope someone from HP will be able to pick this up.
We have a number of ML110 G5 servers which we would like to be able to boot from an HDD attached to SATA port 5 or 6. This was possible with the G4 version of the server (using the PATA ports), but on the G5, these ports are "forcibly" detected as CDROM's by the BIOS as soon as SATA RAID is enabled on the other ports (1-4). This means that the BIOS cannot boot from this device.
The drive is detected correctly in F10 Setup using AUTO or USER, but as soon as the server reboots it is reset to CDROM.
Does anyone have a workaround to allow this, or would HP consider a BIOS update to allow this setting to be retained over a reboot?
Many Thanks,
Nick.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-10-2008 09:13 AM
04-10-2008 09:13 AM
Re: BIOS feature request for ML110 G5
Same problem here :(
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP