- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- [DL360 Series] Can't access RBSU
ProLiant Servers - Netservers
1752719
Members
5679
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-18-2006 09:21 AM
тАО01-18-2006 09:21 AM
On my DL360 (Dual P3 1.13), i am unable to access the RBSU or BIOS. I've read the manual wich tells me to press F9 during system power up. This does not work. Any suggestions? Thanks in advance!
Solved! Go to Solution.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-18-2006 10:07 AM
тАО01-18-2006 10:07 AM
Solution
As I remember, first generation of DL380 did not have RBSU.
It uses special system partition, accessed by F10 right after POST.
Often this partition is deleted by mistake. You can configure server from SmartStart 5.5 (or config diskette).
If you reinstall server from scratch, you can reinstall system partition from SmartStart.
It uses special system partition, accessed by F10 right after POST.
Often this partition is deleted by mistake. You can configure server from SmartStart 5.5 (or config diskette).
If you reinstall server from scratch, you can reinstall system partition from SmartStart.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-18-2006 08:07 PM
тАО01-18-2006 08:07 PM
Re: [DL360 Series] Can't access RBSU
Thanks for the reply.
Very weird, the manual says it does contain a RBSU.
The reason I have to access the RBSU is to change the boot order (I want to boot the server from LAN). I'll give it a go with SmartStart 5.5.
Very weird, the manual says it does contain a RBSU.
The reason I have to access the RBSU is to change the boot order (I want to boot the server from LAN). I'll give it a go with SmartStart 5.5.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP