- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- Re: Dual 5302 in a ML530
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-28-2005 10:10 AM
тАО02-28-2005 10:10 AM
I have a mirror(2 drives - 9.1GB) and a RAID-5 (4 drives 72 GB) in one cage on one channel.
Then in the other cage, I have RAID-5 (six drives) in the other cage on the other channel.
I want to reduce my DISK ques from my SQL server using another 5302 controller.
When I put the second 5302 controller in, I have tried different channels on each controller, but no matter what, the CAGE-2 six drives are recognized, but NOT the ARRAY.
Suggestions?
Both controllers are on 3.54 (latest) firmware. The drives that are NOT being recognized are on B020 and the latest is B022A (36.4GB drives)
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-01-2005 05:07 AM
тАО03-01-2005 05:07 AM
SolutionSteps:
1. Disconnect second Cage from Controller A !
2. Install Controller B in server
3. Update F10 Partition with Newly added HW
4. Power Up to O/S ├в access to ACU delete Array from CAGE B
5. Power Down server
6. Reconnect SCSI cable from Controller B to Cage B
7. Power Up accept drive Position has been changed
8. Should work
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-01-2005 05:12 AM
тАО03-01-2005 05:12 AM
Re: Dual 5302 in a ML530
4. Power Up to O/S, access to ACU delete failed Array from CAGE B if it shows up still
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-01-2005 05:27 AM
тАО03-01-2005 05:27 AM
Re: Dual 5302 in a ML530
The drives show up, just not the array.
Thanks for the clarification.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-01-2005 06:51 AM
тАО03-01-2005 06:51 AM
Re: Dual 5302 in a ML530
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-01-2005 07:05 AM
тАО03-01-2005 07:05 AM
Re: Dual 5302 in a ML530
We did try swapping arrays around f
Controller A port2 Array C vs
Controller A port1 Array C
and with
Controller B port1 Array C vs
Controller B port 2 Arrray C
Drives are always recognized not sure if the array was though. I actually didn't do the work, my colleague did. :/
Previously, we went through one bad array controller (a B controller). It was replaced in warranty, now we are trying it again (third time).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-01-2005 07:26 AM
тАО03-01-2005 07:26 AM
Re: Dual 5302 in a ML530
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-01-2005 07:31 AM
тАО03-01-2005 07:31 AM
Re: Dual 5302 in a ML530
Would this be the same as doing it in the Array Configuration Utility (ACU)?
Or would it be different?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-01-2005 07:48 AM
тАО03-01-2005 07:48 AM
Re: Dual 5302 in a ML530
As you see step #1 Disconnect Cable from Cage B, where when you boot from ACU maximum what you see is failed Array, however you don't have access to it.
When Cable disconnected you only Modify RIS table for Array Configuration around all drives, but you don't loose data.
Where at reconnecting Cable: Back to Controller Redetect Previous Array and automatically Update RIS.
If Cable was connected all Delete option from F8 or ACU will destroy actual Array.
Than you right; you will see all Drives, but no Logical Drives.
First Sign from POST: if Array Detected, is #x of Logical Drives.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-01-2005 07:59 AM
тАО03-01-2005 07:59 AM
Re: Dual 5302 in a ML530
1. Power down server
2. Disconnect second Cage from Controller A
3. Install Controller B in server
4. Update F10 Partition with Newly added HW
5. POST to ARRAY Controller BIOS delete Array from Controller A
6. Power Down server
7. Reconnect SCSI cable from Controller B to Cage B
8. Power Up Server, Controller A recognizes two Arrays, Controller B recognizes drives, but not the third array.
So in the steps you outlined, is changing the ACU for the array the same as changing the array in the Array Controller's BIOS?
1. Disconnect second Cage from Controller A !
2. Install Controller B in server
3. Update F10 Partition with Newly added HW
4. Power Up to O/S ├Г┬в├В ├В access to ACU delete Array from CAGE B
5. Power Down server
6. Reconnect SCSI cable from Controller B to Cage B
7. Power Up accept drive Position has been changed
8. Should work
Thanks for your replies, just trying to get a handle on this, before our maintenance w