- Community Home
- >
- Servers and Operating Systems
- >
- ProLiant
- >
- ProLiant Servers - Netservers
- >
- Re: Error Codes for HP Netserver LH+ 5/166
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-23-2004 11:16 AM
09-23-2004 11:16 AM
Error Codes for HP Netserver LH+ 5/166
I have the latest BIOS and ran the ECU, but couldn't find any explanation for that error code.
I have no OS but everything boots fine, the error isn't a hindrance.
I know that some suggested erasing the CMOS, is there anything else I can do besides that?
What is the meaning of that specific error code?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-24-2004 05:35 AM
09-24-2004 05:35 AM
Re: Error Codes for HP Netserver LH+ 5/166
Configuration corrupted. A)Check the configuration. B)Examine the system board and replace it if defective. C) Check that the software is not corrupting CMOS memory.
This is straight out of the service manual. I would clear cmos first. SW1 3 saves or erases the NVRAM and CMOS. Default is on. Turning it off and powering on and off will erase the current system configuration.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-24-2004 11:30 AM
09-24-2004 11:30 AM
Re: Error Codes for HP Netserver LH+ 5/166
If you get this after a soft reboot (no power cycle), make sure you have saved the config before exiting the ECU.
Dave.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-26-2004 11:32 AM
09-26-2004 11:32 AM
Re: Error Codes for HP Netserver LH+ 5/166
I was wondering from where could I get the service manual?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
01-27-2006 05:42 AM
01-27-2006 05:42 AM
Re: Error Codes for HP Netserver LH+ 5/166
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP